Problem 1:Determine the impedance and the total current.470 50 mH 100 mHf= 100 HzR5V10SolutionZ, = Z, +Z„ +Z +Z= RI + R2 + jal.I+ jol.2= 47+ 10+ j[27x100x(0.05 + 0.1)]=57+ j30.r|z,|=|57+ j30r|= /57' +(30x)' =11092I='s |Z,|= 5/110= 45.4mAProve that my solution is correct (or not)

Given data Resistance is R1 = 47 ohm Resistance is R2 = 10 ohm Inductance is L1 = 50 mH Inductance…

Problem 1: Determine the impedance and the total current. R 4 470 50 mH 100 mH f-100 Hz Solution 2, - Z„ +Z„ +Zu +Z» - RI + R2+ jesl1 + josl.2 -47 + 10+ [2#x100×(0.05 + 0.1)] -57+ j30r IZ,|=|57+ j30=|= /57° +(30r)° =1102 1=s/|Z,\=5/110 = 45.AmA Prove that my solution is correct (or not)

Problem 1: Determine the impedance and the total current. R 4 470 50 mH 100 mH f-100 Hz Solution 2, - Z„ +Z„ +Zu +Z» - RI + R2+ jesl1 + josl.2 -47 + 10+ [2#x100×(0.05 + 0.1)] -57+ j30r IZ,|=|57+ j30=|= /57° +(30r)° =1102 1=s/|Z,\=5/110 = 45.AmA Prove that my solution is correct (or not)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Find out the zero-phase sequence components of the following set of three unbalanced voltage…

Q: For the series R-L-C circuit of Figure Q4: (i) Calculate the total impedance Zr for the frequencies…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 6) Find the capacitive reactance, the impedance and the current of the following resistive and…

A: In this questions, Find the impedance Z= R+jXL -jXc Current I = V/Z XL =wL Xc = 1/wC w= 2πf rad/s…

Q: Impedances Z1 connected in series. Express the total impedance in polar coordinates. (Please check…

Q: In the circuit diagram given in the figure below, L=5 mH, C= 33.33 µF and R = 20 Q. For a voltage…

A: Given circuit shown with L=5 mHC=33.33 μFR=20 ΩVoltage sourcev(t)=28.3cos3000t+45° v

Q: 1) For the circuit in Figure, what is the value of S1, S2, S3, S4 and ST? Response format: a complex…

A: Given loads are 1. (100+55) kW =155 kW at 0.6 power factor (lagging) 2. 200 kVAR at 0.8 power factor…

Q: PROBLEM: V = 1.04/0 P, + jo. 0.5 - j0.2 -1+ j0.5 0.3 - j0.1 3 For the system shown above, the bus…

A: For the given bus admittance matrix,…

Q: A Moving to the next question prevents changes to this answer. Question 1 Refer to the circuit…

A: In this question we will find Norton equivalent impedance seen from 3 A current source..

Q: The circuit shown consists of a source driving a load that consists of the parallel connection of…

A: It is given that: SA=9.216+j6.912 VAZB=42.426∠45°vt=24cos5t+30°V

Q: The circuit is shown in the figure. Z, - 302 2,- 250 it 2, =-j15 n z,=j10n Vs- 110 2-30* Vrms 1)…

A: Brief description : In the above given electrical circuit we need to calculate the value of total…

Q: Q4 For the series R-L-C circuit of Figure Q4: (i) Calculate the total impedance Zr for the…

A: "Since you have posted a question with multiple sub parts we will solve first three subpart for you…

Q: In the circuit shown in Figure 9, w=100rad/s, R=12N, C=500µF, L=160mH and Is rms=2.6A. a) Solve for…

A: a..>>Total impedance seen by the source :-…

Q: Find the equivalent 5.A 3 j1022 130 ن - -jon t jsn Impedance 5A i jas J72

Q: (a) Transform v(t) = 75 cos(377t – 15°) to phasor form. Comment on whether w = 377 appears in your…

A: (a) The given instantaneous signal is, v(t)=75cos377t-15oVmax=75Vrms=752Vrms=53.033 Vω=377ϕ=-15o In…

Q: QUESTION 1 jΒΩ m - Τ 2/0° A RΩ -jΛΩ For the circuit shown above, what is the magnitude of the phasor…

A: given here a electrical network and asked to find the magnitude of V0 .

Q: An Ac series circuit has R=300ohms, L= 0.90H, and C=2.0microfarad with a generator of 50V and w=…

Q: impedance of a series RC circuit is given as (8- j6) ohms and is connected to an ac source of…

A: In this question , we will find capacitive reactance...

Q: Two impedances Z1 = 2 + j4 and Z2 = R + j0 are connected in parallel. Determine R so that the power…

A: First calculate impedance of the two parallel connected elements and than find impedance angle . Now…

Q: 02 of 2) i) Convert i(t) = 4 sin(6t – 60°) A to phasor form: ii) If L = 50mH with w=1000 rad/s, what…

Q: At Zr = (200 + j50) an impedance of Van is connected, (1002 = Z0) %3D %3D to the end of its…

A: Brief description: In electromagnetic theory in the process of smith chart we go for the calculation…

Q: Van = 4160 cos (t - 49°), Vbn = 4160 cos (t - 289°), Vcn = 4160 cos (t + 191°)" (THIS PROBLEM IS…

Q: Question 2: Based on figure below: a. Find the total impedance Z, in polar form b. Draw the…

Q: Super Position theorem a) For the circuit given, Cind the Voltage Vo on ly due to the 6V voltage…

A: For this problem, we have to find value of voltage V0 corresponding to 6V acts alone and 2mA…

Q: 2. Explain why Phasor and impedance diagrams have the same angles. 2 II/L of Phacon shift if D 2000…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 2- Three branch currents in a network are (1)= 2 sin (377t + 45°) A iz() 0.5 cos (377t + 10°) A…

A: Current in the network given Determine the phase angle by a. i1 leads by i2 b. i1 leads by i3…

Q: 3 kN 3 mH ww C1 6 µF R3 1 kN v(t) R2 2 kN ww

Q: Impedances are marked in perunit on a 100MVA. 100 KV base. The load at bus 2 is 52 16MW - 132 MVAR,…

A: In this question we need to find a bus voltage at bus 1 and bus 2 .

Q: Given the circuit below. A U,07t U.077 100-V 3- source b 5260'n 22-30°n Iec 3.1. Determine the…

A: The voltages for given supply is Vab=100∠0°Vbc=100∠-120°Vca=100∠120° The current I is calculated as…

Q: X = 6 N Xc = 10 N ll + UL %3D R = 20 t UC + UR e = 70.7 sin 377t ZT

Q: Question 1: Based on figure below: a. Find the total impedance Z, in polar form b. Draw the…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: Given the circuit below. A 220'n U,07t 100 -v 3-4 source b B U,097$ ICA lạc 22- 30°n Determine the…

A: From the three phase system ..

Q: Question 25 Determine Vbn of a balance three phase circuit for which have Van = 160L30 . 160L-90?…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Q.5: a) Correct any five of the following sentences using suitable scientific phrases. 1. In series…

A: Resistor, inductor and capacitor are the part and parcel of any circuit.

Q: In the circuit shown in Figure 10.23, find the Norton equivalent current In and the Norton…

A: Here norton equivalent impedance and the current have been found.

Q: 8Ω 2 H 5 sin 5t V + 4 H F 12

Q: Impedances are marked in perunit on a 100MVA, 100 KV base. The load at bus 2 is S2= 16MW - j32 MVAR,…

A: In this question We need to find a voltage V1 and V2

Q: 8. Calculate the: a) total impedance; b) total current; c) phase angle , of the circuit shown below:…

A: Given data, R1=200 ΩR2=200 ΩXC=400 ΩXL3=600 ΩXL1=100 ΩXL2=100 ΩV=100 V

Q: In a series-parallel circuit, the parallel branches A and B are in series with C. The impedances are…

Q: If the impedance Z1 = 0 + j10 and the impedance Z2 = 10 - j10 are connected in parallel, the…

Q: L=0.15H R = 120 VR- C=100uF V=100v f=50HZ

A: Series RLC circuit

Q: In the circuit shown in Figure 10.22, find the Norton equivalent current In and the Norton…

Q: Z- Σ3Ω 20 www 50 4ΩΣ -3 Ω Ο a. Zτ = 1,95 + j1,29 Ω Ο b. Ζτ = 1,95 - j0,29 Ω j2 Ω F-3 Ω 3 Ω Ο c. None…

Q: Show that at a given frequency ω, the circuits will have the same impedance between the terminals…

A: Given data The value of frequency is ω rad/sec. Now the impedance of fig. (a) is given by,…

Q: (b) The current through i(t) = Im cos(wt + 30°), Im = 5 mA, w = 6.283 rad/s, and the voltage across…

Q: Find the power factor of the circuit, and indicate whether it is leading or lagging. R-1.8 kn X, - 2…

A: In a RLC series circuit, the value of power factor (pf) of the circuit is given by: Where, The…

Q: Consider the phasor representation shown below of a circuit at 200 Hz for the following two subprob-…

A: In this question, Find the phasor output voltage and time domain voltage for different different…

Q: For the series R-L-C circuit of Figure Q4: (i) Calculate the total impedance Zr for the frequencies…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Reply as soon as possible and clearly, do not use italics 1) For the circuit in Figure, what is the…

Q: In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0•. A load with active…

A: Impedance: Impedance, denoted by the letter Z, is a measurement of electrical resistance. Ohms are…

Q: Question 2. In the circuit below find (a) the line currents laa, IbB, and Iec in polar form (b) the…

A: The circuit can be redrawn as: Where, Va rms=220∠28° VVb rms=220∠-92° VVc rms=220∠148° VWe can see…

Question

Problem 1:
Determine the impedance and the total current.
470 50 mH 100 mH
f= 100 Hz
R
5V
10
Solution
Z, = Z, +Z„ +Z +Z
= RI + R2 + jal.I+ jol.2
= 47+ 10+ j[27x100x(0.05 + 0.1)]
=57+ j30.r
|z,|=|57+ j30r|= /57' +(30x)' =11092
I='s |Z,|= 5/110= 45.4mA
Prove that my solution is correct (or not)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the circuit diagram in figure Q22: which of the following is the total impedance? 12 Ri 10R R2||5R Figure Q22 V 220V40 50HZ L1 315mH C1=350uF O a. 3.33/0° O b. 4.71290°2 O c. 7.3304-19.66° O d. 10.37261.19°2
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE
For the series circuits of the figure below, calculate the total impedance (ZT). R1 4 k2 XL1=4 k2 ZT Xei= 6 k2 Xc2= 3 k2 XL2= 4 k2 Z7= 17.4 kn, the angle is 76.7° Ob. Z7= 17.4 kn, the angle is 56.3° .Oc. Z7= 4.1 kn the angle is -14° Od. Z7= 7.2 kn the angle is 56.3°
QUESTION 5 A resistor, a capacitor, an inductor, and a mystery component are connected in parallel. The resistor has a resistance of 300N, the capacitor has a reactance of 2500, and the inductor has a reactance of 6000. The total impedance of the circuit is 59.52-j119.640. What is the mystery component? O there is no mystery component O resistor O inductor O capacitor
acras C relative Soura? An LRC senes circuit with R:14052 =D27mH, & C = \.9 MF is powered by an ac Voltage source of peak uoltage V9:250V frequency fa48O H&. A) Determine the peak cucrent that flaws in this circuit! B)Determine the phase angle of the Source voltage relative to the current? IDetermine the peak noHage acosi R DIDetermine the phase angle afthe valtage acress R relative to the sourse Peak তिाक F Phase ang le of the uaHage accast Lelative te the source oodage. across L? G Prak untage C. H) Phase anye of the voltage
2. A series RL circuit has voltage and current equations of e = 141.42 sin 2n30t + 141.42 sin 2n90t volts and i = 9.8 sin (2n30t - 30°) + 5.66 sin (2n90t - 60°) amperes. Determine the inductance L. A. 92.5 mH B. 38.3 mH C. 27.22 mH D. 83.49 mH
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
QUESTION 4 A resistor, a capacitor, and an inductor are connected in series with a function generator. The resistor has a resistance of 1.5k2, the inductor has a reactance of 1.2kQ, and the capacitor has a reactance of 2002. The circuit has a total current of 172mA RMS. Find the total voltage. O 310V233.7 O 74.5VL-14° 188V273.2 O 44.4VL-25.3°
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.
If the maximum value of an alternating voltage with a frequency of 35 Hz is 100 V, write the equation for this voltage. A u= 70,7.Sin2,198t B u= 63,6.Sin35t C u= 63,6.Sin35t D u= 100.Sin219,8t E u= 63,6.Sin35t
Two impedances Z1 = 2+j6 N and Z2 = 6-j12 Q are connected in series. What is the resultant impedance in the polar form? 10cis-36.9° O 10cis36.9° 10cis53.1° 10cis-53.1°