Problem 1: Design an equalization basin for the following cyclic flow pattern. Provide 10 percent excess capacity for unexpected flow variations and solid accumulation. Evaluate the impact of equalization on mass loading of BOD, (you need to provide a description). The time interval is 1 hr. Conduct your calculations in an excel spreadsheet and provide the final table as well.

Problem 1: Design an equalization basin for the following cyclic flow pattern. Provide 10 percent excess capacity for unexpected flow variations and solid accumulation. Evaluate the impact of equalization on mass loading of BOD, (you need to provide a description). The time interval is 1 hr. Conduct your calculations in an excel spreadsheet and provide the final table as well.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 12 of 23 A flow os 0.413 m3/s was measured from a rectangular channel flowing 1.20 m wide and 0.60 m deep. If the slope of the channel was 0.0004, what os the roughness of the lining of the channel? Select the correct response: 0.013 0.025 0.021 0.016 < Previous
1. Illustrate what types of basic equations and forces analysis are needed for reservoir and pipe flow 2. Explain the different types of fluid measurement device and its application. 3. Explain the hardy cross method for pipe flow problem solution
NEED ASAP There is a 1350 mm diameter sanitary sewer pipe with roughness coefficient of n = 0.022 and slope of 0.67%. Answer the following questions if the depth of the flow in this pipe is 659 mm: 17. How much is the capacity flow (Qc) of the proposed sanitary pipe? TIP: You may use Table No. 1 to help for calculation of the Qc. 18. How much is the velocity of the capacity flow (Vc) in the proposed sanitary pipe? 19. How much is the actual sanitary flow (Qa) of the project area? 20. How much is the velocity of the actual flow (Va) in the proposed sanitary pipe?
1- Draw a chart with the volumetric flows on the x- axis and Reynolds numbers on the y- axis (if possible use excel). 2 - How is it possible to change Reynolds number while keeping the flow rate constant? Discuss. How ic the rっtodう Erolain。
1 > Solve the arrow diagram network shown below. Compute the values of ES, EF, LS, LF, FF, and TF for the activities. Highlight the critical path. Determine (show calculations) the independent float and interfering float for Activity H. A 2 B O TV/#F W G EET ES EF EET LET LS Duration LF LET F 8 H 9 D 5 E 4 6 K 6 L O 6 P O M 12 N/2
Research and solve your own sample problem for flow measurement (Bernoulli's equation) for the following flowmeters. 1. Venturimeter a. Define b. Explain how it measures flow c. Sample problem using Bernoulli's equation 2. Pitot Tube a. Define b. Explain how it measures flow c. Sample problem using Bernoulli's equation
1.) total head loss from A to D equal to 9m. The flow rate of the pipe system shown in the figure shown is 50 Liters/sec under a PIPES Length (m) Diameter (mm) Нazen, C A 400 200 130 366 160 130 290 ? 130 D 610 250 130 B) A) Determine the Following: d. Head loss of pipeline B. e. Discharge of pipeline C. f. Diameter of pipeline C.
Question 4 The time of concentration of a 5.8ha catchment has been estimated as 33 minutes. Estimate the peak rate of runoff for a storm with an intensity of 49mm/hr and a duration of 22 minutes. Assume the coefficient of runoff as 0.61 and the time-area relationship to be linear. Present the result in the unit of m³/s and keep two decimal points (i.e to the accuracy of 0.01). Your Answer: Answer need it ASAP question 4
The three water filled tanks shownin the figure are connected by pipesas indicated. If minor losses areneglected, determine the flow ratein each pipe.
notes for the question and actual picture is the question thank you Although the following procedures are more or less sequential, be certain you read through and understand all the procedures and suggestions before you begin to actually construct a flow net. 1. Ensure that the use of a flow net is valid. (a) Flow is steady state. (b) Boundary conditions are known or can be approximated well. 2. Prepare for a trial-and-error solution: there is no unique solution. 3. Ensure that the boundaries of the flow field are drawn to scale. 4. Define the boundaries, and determine the nature of each boundary (a) equipotential, or constant-head, boundary (b) flow line, or no-flow, boundary: commonly an impermeable boundary (c) known-head boundary; commonly the water table (d) most often encountered, two equipotential boundaries and two flow line boundaries. 5. Determine the symmetry of the flow field, if any. This may reduce the work involved-for example, bilateral symmetry would require…
ual Marks. Q1: Given below are the flows from a storm of 1hr duration on a stream with a drainage area of 1000 km². Assume a constant base flow of 800m³/s. Drive the ordinates of a 2hr UH for the basin and state its peak. 1 2 Time (hr) Flow (m³/s) 3 4 5 6 7 8 9 800 900 1000 2000 1800 1600 1300 1000 800 Q2: A lako wid
QUESTION 1 A 1-hr, 1 cm unit hydrograph (UH) is presented in the table below. 4 Time (hr) UH (m³/s) 80 0 0 1 25 250 a) Convert the 1-hr UH to a 3-hr UH. b) What is the area of the watershed? 3 100 5 60 deb biences nama A PO CONNA 6 40 nong 7 20