Problem 1: Calculate the axial stress in each part of this assembly if the ID of the steel tube 150mm,radius of the steel baseplate is 175mm and the concrete pedestal is replaced with a 200mm squareconcrete pedestal. If the steel tube is 3 meters tall and the pedestal is 1.25 meters tall, what is thedeflection in each? Assume Econc = 25 GPa.500 KIN-100 mm

Answered: Image /qna-images/answer/3c55387b-997c-4ab0-9c3c-214ac4ac2728.jpg

Problem 1: Calculate the axial stress in each part of this assembly if the ID of the steel tub radius of the steel baseplate is 175mm and the concrete pedestal is replaced with a 200m concrete pedestal. If the steel tube is 3 meters tall and the pedestal is 1.25 meters tall, w deflection in each? Assume Econc = 25 GPa. 500 AN

Problem 1: Calculate the axial stress in each part of this assembly if the ID of the steel tub radius of the steel baseplate is 175mm and the concrete pedestal is replaced with a 200m concrete pedestal. If the steel tube is 3 meters tall and the pedestal is 1.25 meters tall, w deflection in each? Assume Econc = 25 GPa. 500 AN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F = 300 N and the cross sectional area of the rod is 200 mm2 , determine the stress in the section of copper. ... Сopper Steel 2F F 3m 2m A) 1.5 MPa В 0.75 MPa 3.0 MPа D 4.5 MPa
A flat steel bar, 28 mm wide by 2 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 22 mm. Compute the maximum stress in the bar Use E = 230 GPa. Answer must be in MPa.
An aluminum [E = 10400 ksi] control rod with a circular cross section must not stretch more than 0.39 in. when the tension in the rod is 2310 lb. If the maximum allowable normal stress in the rod is 12 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = i (b) L= i in. in.
3. The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter B® L=2.4 m 50 mm diameter L=1.9 m 30 mm diameter rigid support @ D
2. Calculate the increase in stress in each segment of the compound bar if the temperature is increased by 80°F. Assume that the supports are Aluminum Steel unyielding and use the following data: A (in') E (psi) « (°F) 10 x 10 12.8 x 10 29 x 10 6.5 x 10 Aluminum 1.5 2.0 -10 in- 15 in.- Steel
PROBLEM 3 A compound shaft consisting of a 50mm diameter bronze segment and a 75mm diameter aluminum segment is subjected to two torques shown. Determine the maximum permissible value of T if the stress of bronze is limited to 60Mpa, the stress in aluminum is limited to 70mpa and the angle of twist of the free end is 10 deg. G for aluminum= 28GPA and G for bronze = 35 GPa. 27 37 Aluminum bronze it 2M 2
2.50 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-sectional area 1400 mm², as shown in the figure. The cross-sectional area of the aluminum bar is 2800 mm?. Compute the stress in the aluminum bar after the 400-kN load is applied. Use E = 200 GPa for steel and E = 70 GPa for alumi- num. Neglect the weight of the platform.
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid A36 steel with a 20 mm diameter (E = 200 GPa). Outer sections DA and BC are solid red brass (E = 101 GPa) with a 50 mm diameter. A previous analysis by a now departed coworker correctly determined that the internal normal stress in DA was 54.952 MPa compression. You are asked to determine the horizontal displacements of joints A and B.
| 400 kN 0.1 mm Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-sectional area 1400mm 2. as shown in the figure. The cross-sectional area of the aluminum bar is 2800 mm 2. Compute the stress in the aluminum bar after the 400-kN load is applied. Use E=200GPA for steel and E=70GPA for aluminum. Neglect the weight of the platform. Steel Aluminum Steel -250 mm
A rigid block AB of weight 800 N hangs on an equally spaced vertical wires, two of steel and one aluminum. The wires also support a load P acting at the midpoint of the block. The diameter of the steel wire is 2 mm and that of aluminum wire is 4 mm. what load P can be supported if the allowable stress in the steel wires is 220 MPa and in the aluminum wire is 80 MPa. Use E = 200 GPa for steel and 70 GPa for aluminum. ////// St Al St A W = 800 N
Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. 900 mm B 80 mm, 40 mm