Print Reading for Industry 432 Class Date Name Industry Print Exercise 22-2 Refier to the print PR 22-2 amd answer the questions belou 1. What is the total number of parts (not part numbers) required for this welded assembly? 2. What is the name and number of the part identified as item 3? 3 According to note 3, what section of the AWS D1.1 standard should be referenced for the 100% weld penetration? 4 What type of weld should be used to "tack" the parts associated with item 4 in place? 5. What process can be used after welding to blend the weld with the parts? 6. For the process in question 5, does the welding symbol indicate flat, convex, or concave? 7. A couple of the welding symbols have a circle on the symbol elbow. What does that mean? 8. Are there complete dimensions on the drawing detailing all measurements for the individual parts? 9. Unless specified, all welds are to be class Review questions based on previous units: 10. Are there cutting-plane lines shown on this print? 11. What scale are the main views on the original drawing? 12. How much does this part weigh after welded together? 13. What revision status was given to this print? 14. What is the length of each of the six spacers? 15. At what scale is the enlarged detail? Copyright Goodheart-Willcox Co., Inc. Welding Prints Unit 22 ВС128 N8 fiblaeo N D i no elodie va y biar wot 101 C 90 Tou @T Print supplied by Marathon LeTourneau Cc PR 22-2. Stress Relieved Sub-Str. Copyright Goodheart-Willcox Co., Inc. SLONTOI3 ECN DATE APPROVED ZONE REV DESCRIPTION ERT WF OO RELEASED BLENDED FILLET WELD 62 - I REF 무oz FULL SCALE WELD JO INT BLEND FILLET WELD HERE BY GRINDING REF WELD PROCEDURE NUMBER IS WEZ002SBUF WELD PROCEDURE NUMBER IS WEZ002SBUF Е (SEE INSPEC- TION NOTE) (SEE INSPEC- TION NOTE) BLEND FILLET WELD HERE BY GRINDING VTAC TYP 4 LOCATION NOT CRITICAL, FOR STRESS RELIEF ONY REF ITEM 5 USED ON ITEM 2 54 REF NMOHN SHINON SI ONY BC238 BACK ING BAR BC237 SPACER, TEMPO PLATE, INNER ROLL-UP, INNER PLATE, OUTER NOTE: BC236 Е BC235 NOTES: i. STRESS RELIEVE PER ERP 062 AFTER FABRICATION. 3. WELD TO BE COMPLETE JOINT PENETRATION (100%) UT TO SECTION 9 OF AWS DI.1 1992 EDITION. MAGNAFLUX PRIOR TO UT. NO CRACKS ALLOWED ALL WELDS CLASS IV UNLESS OTHERWISE SPECIFIED. (AWS D14.4) BC234 ITEM PART NO. QTY DESCRIPTION REVIEW AND APPROVAL FIRST USED ONVCONTRACT NO. THIS DRAWING AND ALL DATA THEREIN IS THE OINENSIONS ARE IN INCHES TOLERANCESI Marathon LeTourneau Company BR549 PROPERTY OF MARATHON LETOURNEAU COMPANY LONGVIEW, TEXAS IT IS CONIDENT LAL FG ENGR Longyie Division ANGLES 1 2 PLACE DECIMAL.03 O1-21 MDF NAO 12-9 SUB-STR, STRESS 12-9 REL IEVED ETALLURGISTROGERS 12-10 -01-9 SIO TMI030 30Vd E IND ENGR TROY FRACTIONAL a1/16 12-10 ENGA 12-10 PROD ENGA TOBI 3 JON IS O TOOL ENGR MDF OTY SUBJECT TO RETURN BC128 ON FOS 3IS 6-21 ON OAO SI ON ONVM30 NOen 12-10 J APPROVAL HJUK TEXTURE DESIGNATIONS APPLY BEFORE PLATING 6-21 ANY WAY DETRIMENTAL MATERIAL 8/1S 5022 LBs 00 TO OUR INTEREST SHEET 1 OF 1 SONIIVO HSINIA O

Question 7 Identify the drawings as isometric, trimetric, oblique or perspective. A OFrpent -isome Arpenoect De c E-trinetc Foln O oect anseot ed he O t wwec Comei D - c Aomtc Canet onat E ic Bri D Fro OApere -onetic CnnD o Dreulos D.

So how would you go about doing letter C using plus or minus method/ equal bilateral expression??thank you!!!

Only answer the graph portion, the image of the bolt is invade the area or length is relevant

please do a step by step process of the equation breaking it down for me

What is the max circularity, on a radius, on the part below before a feature control frame is applied? Please refer to image attached.

I need answers to parts 1, 2, and 3, pertaining to the print provided.

Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…

What is compression testing?

Refer to drawing 21A033, what is dimension G?  (Please note that you can't just assume the hub protrudes equally on both sides as it may not)   All abbreviations are standard