pressure readings can only be taken in an open container Gauge Hyśdrostatic Vacuum Absolute

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: How much will an air leak cost during three monthes? the hole has a diameter 6.35mm at line pressure…

A: Given  Hole diameter D=6.35 mm Line Pressure P= 690 kPa Electricity Cost  C=7  centskwh Time of air…

Q: Which of the following statements is not true? Select one: O a. Reports can contain bulleted or…

A: As we know Equations should be written in a symmetric manner, not just in the left margin. Equation…

Q: for it because many people confuse it with something else so this time I am attaching a picture of a…

A: Required Torque Given data Key dimension are given Shaft diameter is given Allowing stress is also…

Q: Consider an air-standard Diesel cycle. Operating data at principal states in the cycle are given in…

A:

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: The correct choice is what

A:

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: Could you solve the last 3 options (c, d, e) please

A:

Q: can you solve the question with hand written notes in details

A:

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

A:

Q: Give one problem solving question about "Method of Sections" and show the solution

A:

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: please answer final two parts thank you

A:

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: _1. He is an English man credited for the invention of a screw cutting lathe. _2. A man from New…

A: Identification test :

Q: where did you get 0.157

A: Given:Figure with dimension is providedTo find:Percent reductions in areaPercent reduction in area…

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: Whats the final answer if it requires the final answer in newton?

A: We have-a) The moment at point O is 100.56 lb-ft (counter clockwise)b) The magnitude of the…

Q: If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with…

A: Given Data⇒ Load intensity for rectangular section : F=4 KNm Distance upon which load is…

Q: I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps…

A: In general revision changes are indicated in two methods.Cloud method- the recent change information…

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: 3. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: why

A: Equating moment at A to find force in rod BC.

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: 2. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: Thank you . But where did you get 12 from ?

A: Given- The width of the rectangular beam b = 140mm The depth of the rectangular beam h = 110 mm…

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: Note: (1) n is the student's number in the class. (2) All dimensions are in cm. (3) Dimensions need…

A: An Engineering drawing is a technical drawing.It purpose is to give information of the product for…

Q: can tutor explain the what is all of the equations means and also answer the next 2 questions

A: To solve the physics problems, let's break them down one by one:1) Calculate the force experienced…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: 2. A composite furnace wall is made up of a 14 in. lining of magnetite refractory brick, a 5.3 in.…

A: Given data as per the question The thickness of brick =14 in The thickness of magnesia =5.3 in The…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.