practice problems #1 Structural Steel Practice Assignment Design joists, beams, and girders for the roof of a structural steel frame building with the information provided below Need to do Design a typical K-series joist. Design a W-shapes for the following: ☑ Exterior beam ☑ Exterior girder ☑ Interior girder Check each section for moment and deflection only. Aallow= 1/240. Compute the axial loads the (4) columns of a corner bay will support. Given VALUES 30' x 30' bays. 3 bays each side of building. Beams and joists spaced 6'-0” (o.c.). Exterior wall = 100 lb/ft Snow load 22 psf Roof Deck 1 1/2" Type B 22 Gage Deck Roof mechanical = 22 psf PLANS: ☑A Roof system framing plan with designed OWSJ, W-shapes, and deck information. ☑Plan can be hand-done

practice problems #1 Structural Steel Practice Assignment Design joists, beams, and girders for the roof of a structural steel frame building with the information provided below Need to do Design a typical K-series joist. Design a W-shapes for the following: ☑ Exterior beam ☑ Exterior girder ☑ Interior girder Check each section for moment and deflection only. Aallow= 1/240. Compute the axial loads the (4) columns of a corner bay will support. Given VALUES 30' x 30' bays. 3 bays each side of building. Beams and joists spaced 6'-0” (o.c.). Exterior wall = 100 lb/ft Snow load 22 psf Roof Deck 1 1/2" Type B 22 Gage Deck Roof mechanical = 22 psf PLANS: ☑A Roof system framing plan with designed OWSJ, W-shapes, and deck information. ☑Plan can be hand-done

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

A beam has an f'c = 5000 psi, fy = 60000 psi, reinforcement ratio = 0.0137. Which of the following is most likely true about the strain in the extreme tension steel? Use the tables posted to Canvas as needed (The ones in the back of the book). The strain is = 0.005
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 28 kips, w = 3.8 kips/ft, LAB = 4.6 ft, Lec = 4.6 ft, and Lco = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. %3D %3D B |C D LAB LBC LCD Answer: Omax = ksi
Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of two #6 (each #6 bar has a section area of 0.44 square inches). Concrete fc'=3000 psi. Rebar yield strength fy=60 ksi. What is the section's theoretical nominal bending moment capacity in ft-k? loll O A. 65.8 ft-k. OB. 57.0 ft-k. OC. 34.1 ft-k. OD. 29.7 fft-k. X²N 16"
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)
The shown is a beam-column connection. Assuming normal weight concrete, f'c = 5000 psi, fy = 60 ksi and all the steel bars are uncoated. The top tension bars are # 9 bars and the bottom compression bars are # 8 bars. Column X2 X3 21.56 in. 17.25 in. 27.6 in. a 34.5 in. X1 Tension Steel I Compression I Steel a 4 Beam d b Beam Dimension and Reinforcement: b = 16 in., d =24 in. clear cover = 1.5 in. Stirrups are # 3 bars with 6 in. spacing. A, = 4# 9 bars, A', =2 # 8 bars The total cross-sectional area of the column ties confining the hooked bars are 1.38 in.² The minimum distance "X2" required by ACI 318-19 code is most nearly equal to: As A's Sec.a- a
What is the total girder and column factor of a joint? O >1 O 2 O 1
Analyze truss using method of joints.
MAKE ONLY 1 PROBLEM. THE PROBLEM SHOULD BE ALL ABOUT *truss analysis: method of member* IT SHOULD HAVE THE FOLLOWING: QUESTION GIVEN REQUIRED DIAGRAM BRIEF EXPLANATIONS SOLUTION FINAL ANSWER MAKE IT ORIGINAL
The following diagram shows a partial floor framing plan of an elevated walkway building connecting an airport terminal building to the adjacent garage. The concrete floor is not post- tensioned. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Framing members are not exposed to weather or in contact with soil. Use ASCE Table 4.1 to determine the design live load for this floor. 30-0¹ S Colm- Ö 90-0 - Mark 54 59 25 30-0¹ N BI -Sinder ASCE 7-10 Chapter 4 Live Load.pdf 50 psf 60 psf 100 psf 150 psf 2
Design the purlin between two trusses spaced 3m apart to support 0.19 KPa roofing. Spacing of purlins is 0.50m on centers. Allowable bending stress is 12.84 MPa, allowable shearing stress is 0.70 MPa and allowable deflection is L To 0.50m $ 3m b=? 2m d=?
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc = 5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. %3D D B LAB LBC LCD Answer: ksi Omax
A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @ FACE OF SUPPORTS TOP BARS 2-∅20 mm 5-∅20 mm BOTTOM BARS 3-∅20 mm 2-∅20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: Tensile steel ratio in positive bending at midspan = __________ (in 5 decimal places) Design Moment strength of section at midspan for positive bending = ___________ kN·m (nearest whole number) Nominal Moment strength of section at face of support for negative bending = ___________ kN·m (nearest whole number)