-pot the series RC circuit in Fig. 14.7: a) Find the transfer function between the source voltage and the output voltage. b) Determine an equation for the cutoff frequency in the series RC circuit. c) Choose values for R and C that will yield a low- pass filter with a cutoff frequency of 3 kHz. Solution a) To derive an expression for the transfer function, we first construct the s-domain equivalent of the Figure 14.7 AA series RC low-pass filter. R w V/s) ( Figure 14.8 A The s-domain equivalent for the circuit in Fig. 14

-pot the series RC circuit in Fig. 14.7: a) Find the transfer function between the source voltage and the output voltage. b) Determine an equation for the cutoff frequency in the series RC circuit. c) Choose values for R and C that will yield a low- pass filter with a cutoff frequency of 3 kHz. Solution a) To derive an expression for the transfer function, we first construct the s-domain equivalent of the Figure 14.7 AA series RC low-pass filter. R w V/s) ( Figure 14.8 A The s-domain equivalent for the circuit in Fig. 14

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please show all steps clearly, thank you.
Q1 Electronics 3
You are designing an FIR filter based on a window function. What is the purpose of the window function? Explain the side effects of the window function to the frequency response of the fir filter. Given a certain specification of the fir filter to be designed, what are the two factors of the fir filter that are determined by the chosen window function?
First calculate the transfer function H(z) from the following difference equation.Then extract the filter parameters (as and bs) that are rquired to implement this filter in Python. y[n] = 2y[n-2] + 7y[n-1] + 4x[n] a = .. , .. , .. , .. b = .. , .. , .. , .. Please show me step by step to understand it clearly
QUESTION 4 b) The magnitude plot of a transfer function G(s)=- K(1+0.55X1+as) s(1+s/8X1+bsX1+s/36) shown in Figure Q4b. Determine K, a and b from the plot. 0 dB/dec +20 dB/dec -20 dB/dec -20 dB/dec dB 0 dB 0 dB/dec -40 dBAdec Hand written plz 8 24 36 Figure Q4b Bode plot of a system
14.20 Calculate the center frequency, the bandwidth, and the quality factor of a bandpass filter that has an upper cutoff frequency of 121 krad/s and a lower cutoff frequency of 100 krad/s.
14.2 Consider the low-pass filter in Fig. P14.2, which has a load resistor R1. a) What is the transfer function of the unloaded filter? b) What is the transfer function of the loaded filter? c) Compare the transfer function of the unloaded filter in part (a) and the transfer function of the loaded filter in part (b). Are the cutoff frequen- cies different? Are the passband gains different? d) If R = 330 N and L = 10 mH, what is the cutoff frequency of the unloaded filter in rad/s?
Analogue Electronics II Design 2 different configurations of active band pass filter for the frequency with bandwidthof 200 Hz.Design A has the quality factor Q less than 10, is independent on the critical frequency,whereas Design B has the quality factor, Q more than 30, is dependent on the criticalfrequency. You can use your own value of resistors and capacitors in the design. Show allrelated calculations (eg. fc, fo, Q, Gain, Bandwidth) and the final circuit design.
How did they get c) d) e) f) g)?
14.- Suppose you need to process a signal with a bandwidth of +-5KHz and you cannot sacrifice its spectral components. What is the minimum sampling frequency and its cutoff frequency of the anti-alias lowpass filter?
QUESTION 4 Q4.1 Show how can a series RLC can be used as a crude band-reject filter? Q4.2 How would you determine the centre frequency for this filter? Q4.3 Show how a graph of H(jo) versus oo for this filter will look like. Q4.4 In the graph, show the possible locations of the centre frequency, and the two cutoff frequencies. Justify why you chose these locations in the graph.
Q4. (a) Write brief notes (taking a maximum of 10 minutes, i.e. minute") on RC filter circuits, including in your discussion: • RC circuit layouts for low pass (LPF) and high pass (HPF) filters. Labelled plots of their frequency responses (i.e. bode plots). • One common LPF application and one common HPF application.