Pls answer w/ complete solution. Asap (Transportation Engineering) Determine the thickness base and subgrade of flexible pavement if the wheel load is 90 kN and has wheel contact area of 88075 sq. mm.. Strength capacity of base is 0.35 MPa and 0.15 MPa for Subgrade.

Pls answer w/ complete solution. Asap (Transportation Engineering) Determine the thickness base and subgrade of flexible pavement if the wheel load is 90 kN and has wheel contact area of 88075 sq. mm.. Strength capacity of base is 0.35 MPa and 0.15 MPa for Subgrade.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter20: Design Of Rigid Pavements

Section: Chapter Questions

Problem 22P

See similar textbooks

Related questions

Q: A vertical pole, cantilevered at the bottom has a solid circular cross-section of diameter, d = 49.2...

Q: An earthquake is usually measured by the magnitude M on the Richterscale. The intensity of the earth...

Q: A 300mm by 600mm rectangular beam is subjected to uniform ultimate load of Wu=200kN/m over the whole...

A: Given data width b = 300 mm Total depth h 600 mm Uniform Load Wu = 200 Kn/m Beam span L = 4 m Comp...

Q: Three tanks are installed side by side in a field to measure the evapotranspiration of rice. Tank A ...

Q: A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 142...

Q: What is the difference between low, medium and high carbon steels? Please put different uses for eac...

Q: Geotechnical

Q: Rework Prob. 8-12, considering the y axis. Prob. 8-12 Find the values of S and Z and the shape fac...

A: To Find - Find the values of S and Z and the shape factor about the horizontal x axes.

Q: The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is sub...

A: To determine the average normal stress in the reinforcing rods. Given, Axial force on the column (...

Q: Instructions. For the given data, provide the following. • Complete Network Diagram highlighting the...

A: Total float = LF - ES - tij Free float = EF - ES - tij

Q: 5. Determine 8g and eg. Let q = 15 kN/m and L = 6m. _B L L 3 3

Q: Moment due to flange Moment due to web Total steel requirement

A: Given data: L = 4.3 m C/C Spacing = 3 m bw = 350 mm d = 470 mm tf = 75 mm f’c = 21 MPa fy = 420 MPa ...

Q: 36 mmø 2.1.m 1.3m 1.2 m w=80 kN

Q: A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). Th...

A: Given data, Ultimate strength of cast iron in compression = 50 ksi FOS = 3.5 Outer dia of pier = 4.5...

Q: A circular bar AB of polar moment of inertia I, and length L is fixed at both ends (see figure). A d...

Q: The state of plane strain at a point is ɛ = 800 x 10-6, ɛ, = 200 × 10-6 and y. = -600 x 10-6, If mat...

Q: A sphere is fired downwards into a medium with an initial speed of 27.76 m/s. If it experiences a de...

Q: astic modulus of E = 77 GPa. The steel rc and c- 1.1 m. What is the magnitude of l- %3D a to

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area o...

Q: Find Void ratio

A: Introduction : Void ratio is ratio of volume of void upon volume of solids Given data : The value o...

Q: tô bé lifted and invers a 5hp motor to lift 50 lbs through 40 onds through 40 ft

Q: Determine a set of values b, d and As for a rectangular beam that will carry a factored bending mome...

A: Given Data -

Q: Determine a set of values b, d and As for a rectangular beam that will carry a factored bending mome...

Q: a. Calculate the flow rate out of the reservoir, if at the discharge (point C) the cros sectional ar...

A: Given -

Q: the farm water requirement is 18.73 mm/day, the water duty in lps/ha is Answer:

Q: A reservoir with as surface area of 300 hectares had the following average values of climate paramet...

Q: The traffic intensity of a certain freeway is 0.833. The arrival rate of vehicles at a certain inter...

A: The given values are as follows,The freeway =0.833The arrival time =200 veh/hrTo Determine The servi...

Q: Determine the force and couple moment reactions exerted by the nut and bolt on the loaded bracket at...

Q: A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 280 lb-ft and T...

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the fig...

A: Given:

Q: 1. Macts in a vertical plane. Find bending stress 30 50 30 M = 20KN- m %3D 30 30 Dimension in mm at ...

Q: A circular bar AB of polar moment of inertia I and length L is fixed at both ends (see figure). A di...

Q: A continuous beam ABC is subjected to a concentrated point load of 10 kN on span AB and a uniformly ...

Q: A cube made of aluminium of dimension 0.1 m x 0.1 m x 0.1 m, rests against a rigid wall as shown in ...

Q: A catchment has six main gauge stations. In a year, the annual rainfall recorded by the gauges are a...

Q: Determine the maximum deflection of the beam loaded as shown. Let Mo = 75 KN.m dL = 3 m. El is const...

A: ##Calculation of Maximum Deflection ###

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

Q: Suppose that a fluid with a density of 1000kg/m3 flowing through a horizontal pipe at a speed of 5m/...

Q: 1. A reservoir with a surface area of 300 ha had the following average values of parameters during t...

A: Given data, Surface area of reservoir = 300 ha. To find out the average daily evaporation from la...

Q: Problem 3.10 12 in. 15 in. 4 #10 bars $3 in. f, = 60,000 psi f = 4,000 psi 18 in.-

Q: Use the fact that the volume of a tetrahedron with adjacent edges given by the vectors u, v and w is...

Q: Q.2. A concrete mix of (1 : 1.5 : z) by weight, The cement factor of this mix is (8 sack/1 m³), and ...

Q: Evapotranspiration in an 8 ha farm is 7 mm/day and percolation losses is 2 mm/day. What is the desig...

Q: Giam (m) (w2) weight of dry ht ar moist soil 1.85 lbs Soil 1.5 (bs GE 2.68

A: Given data, Weight of moist soil = 1.85 lbs Weight of dry soil = 1.5 lbs To find out the water co...

Q: hich gives plants rigidity. When there is insufficient water to create turgor, the plant wilts. Sele...

A: True

Q: Question 2 A tubular post of outer diameter d, is guyed by two cables fitted with turnbuckles (see f...

Q: The table summarizes the distribution of students by college. Use Slovin’s Formula to determine a pr...

A: Let N be the population size of the society or community considered. Let e be the marginal error bas...

Q: 1. For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the...

Q: Find the values of S and Z and the shape factor about the horizontal x axes, for the sections shown ...

Q: 1. Detemine seepage in ft/day per linear foot of the following sheet pile: Sheet Pile 20 GROUND LEVE...

A: Dear student, Please find the answer in the below attachments Thank you

Concept explainers

Design of pavements

Pavement is a structure that is made up of different layers such as sub-base course layer, base course layer, binder course, and a surface course formed with different materials such as gravel, above the subgrade soil constructed to act as a path or carriageway enabling the movement of vehicles. The surface of the pavement should possess characteristics such as adequate friction, light reflection, and drainage. The pavements are classified based on structural design into rigid pavements, flexible pavements, composite pavements, and unpaved pavements. The process of determining a suitable pavement type, its constituent layers, and its thickness is called pavement design.

Question

Pls answer w/ complete solution. Asap (Transportation Engineering)

Determine the thickness base and subgrade of flexible pavement if the wheel load is 90 kN and has wheel contact area of 88075 sq. mm.. Strength capacity of base is 0.35 MPa and 0.15 MPa for Subgrade.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Flexible pavement

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show complete solution and clear explanation thank you A flexible pavement having a thickness of 46mm carries a static wheel load of W. The circular contact has an equivalent radius of 150mm. If the load W is assumed to be transmitted across a wide are of subgrade at an angle of 45 degrees compute the value of the wheel load W if the bearing stress of the base is 0.42 MPa
Question 13 A rigid pavement has a wheel load capacity of 59.92 kN. The allowable tensile stress of concrete is 1.29 MPa. Determine the thickness fcm) of the pavement if dowels are negligible Express your answer in 1 decimal place. A Moving to another question will save this response 8< Question 13 of 50 acer F11 F12 PrtSc Pause Del Home PgL F6 F7 F8 F9 F10 F4 F5 Scr Lk SysRq Break Ins DIO & Backspace 5 € 6. 7 8 9. R Y
Show complete solution with clear explanation thanks A rigid pavement is to be used to carry a wheel load of 49KN, the allowable tensile stress of the concrete is 1.4MPa. Sufficient dowels are used across the joints. Design the center of the thickness of the pavement at the center and base
A rigid pavement is to be used to carry a wheel load of 53.5 kN. Design the thickness at the edge and at the center of the pavement. The allowable tensile stress of concrete is 1.38 MPa. Sufficient dowels are used across the joints.
Find the safe static wheel load that a 360 mm thick rigid pavement could carry without any dowel across the joints if the allowable tensile stress of concrete is 1.5 MPa.
Mark the correct statement: a) The ISC steps are: Compaction, Expansion and Simple Axial Compression b) The MR Resilience Module measures the variation in stress with permanent deformation, there is no rupture in the test c) The MR Resilience Module can be performed in a triaxial cell and dynamic loading that best represents the pavement
A rigid pavement is to be used to carry a wheel load of 54.04 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.44 MPa. Round off to the nearest whole number.
A rigid pavement is to be designed for a wheel load of 53.5 kN. If the tensile strength of concrete is taken as 1.38, determine the required thickness assuming sufficient dowels and tie bars are provided.
A rigid pavement is designed with a 11-inch slab, an E_c of 6 million Ib/in^2, a concrete modulus of rupture of 432 Ib/in^2, a load transfer coefficient of 3.0, an initial PSI of 4.50, and a TSI of 2.5. The overall standard deviation is 0.56, the modulus of subgrade reaction is 190 Ib/in^3, and a reliability of 90% is used along with a drainage coefficient of 0.87. The pavement is designed assuming that traffic is composed entirely of trucks (50 per day). Each truck has one 20-kip single axle and one 42-kip tandem axle (the effect of all other vehicles is ignored). A section of this road is to be replaced (due to different subgrade characteristics) with a flexible pavement having a SN of 5 and is expected to last the same number of years as the rigid pavement. What is the assumed soil resilient modulus? (Assume that all other factors are the same as for the rigid pavement). Please report your answer as a decimal in units of Ib/in^2. For example, report 3000.6 Ib/in^2 as 3000.6.
1. All the below assumptions allow for Elastic Layered Solution of flexible pavement response except (a)Loading area is circular (b)Materials are isotropic (c) Materials are homogeneous (d)Materials properties are stress dependent
Determine the thickness of a rigid pavement with a wheel load capacity of 54 kN, if the allowable tensile stress of the concrete is 1.6 MPa. Neglect the effect of dowels.
4.13) A rigid pavement is being designed with the same parameters as used in Problem 4.5. The modulus of subgrade reaction is 300 1b/in? and the slab thickness is determined to be 8.5 inches. The load transfer coefficient is 3.0, the drainage coefficient is 1.0, and the modulus of elasticity is 4 million Ib/in?. What is the design modulus of rupture? (Assume that any parameters not given in this problem are the same as those given in Problem 4.5.) 4.5 has been added for reference.