Please use the Perry's CHE Handbook for this. Thank you.    Find the viscosity of the ff. fluids in specific temp 1. Water at 35°C 2. Acetone at 25°C

Q: Briefly Explain the factors that affecting evaporation?

A:

Q: i mal

A:

Q: Calculate the density of oxygen gas at a temperature of 57 C and a pressure of 5 MPa.

A: Density of oxygen at 570C and 5 MPa is asked

Q: for the

A:

Q: How will you calculate the pressure drop for liquid passing through a packed bed? And what will be…

A: Introduction As fluid flows through a packed bed it experiences a pressure loss due to friction. The…

Q: Describe the difference between average pressure and false pressure

A: The force applied perpendicular to the surface of an object per unit area over which that force is…

Q: It is said that inlet gas takes 5-6 turns in Cyclone Separator.Justify the statement.

A:

Q: Briefly explain the concept of steady state as it applies to diffusion

A: Diffusion is the process through which particles, molecules, or substances spread or travel from a…

Q: consider that a polystyrene (PS) has the molar mass distributions shown in the table below.…

A: The numerical fraction and the mass fraction along with the corresponding molar mass is given in the…

Q: Estimation of the viscosity of a dense gas. Estimate the viscosity of NITROGEN at 65°F and 1000…

A: It is given that nitrogen gas is at temperature of 65oF and pressure of 1000 psig.

Q: With an aid of a diagram, compare between FOUR (4) ideal gas flow patterns in a membrane separator

A: ideally there are four different flow patterns for membrane separation process:1)complete…

Q: The calculated surface tensión of a liquid at 20degC is 30 dynes/cm while the data from the Perry's…

A: During performing the experiment for finding the surface tension at 20 0C of a liquid where the…

Q: 4- Prove the continuity equation.

A:

Q: What is the typical electrical conductivity value/range for semiconducting materials? 10^-20 to 10^7…

A: Semiconducting materials:  In this type of material there are no free electrons at the normal…

Q: Derive the dimension ratio c/a for regular HCP crystal.

A: HCP crystal Lattice or Hexagonal Closed Packing Lattice is shown below. It is said to find the…

Q: please give a precise answer

A: In summary it is due to :  1. Metals have larger number of free electrons2. Metal have smaller gap…

Q: 7. Calculate the viscosity (micropoises) of molecular oxygen at 273.2 K and 1 bar. The molecular…

A: Temperature, T = 273.2 K Pressure, P = 1 bar Molecular diameter, d = 0.360 nm

Q: Write if the statement is correct. Else, write the correct answer based on the underlined word(s).…

A:

Q: can u explain why more about the equation u use to calculate the specific area of adsorbent.

A: To explain about the equation  used to calculate the specific area of adsorbent

Q: Can you comment on the effect of molecular weight on tensile strength and viscosity. Give me…

A: The tensile strength of polymer is the maximum force or weight that the polymer is going to be…

Q: In the table below are shear stress and shear rate data for three bottles of syrup (simply…

A: In the above question shear stress vs shear rate data are given. We have to find the Non Newtonian…

Q: bläi 3 Comparing polymers to ceramic , compoiste and metals, one can * :find that the polymers have…

A: The correct option regarding the properties of the polymer as compared to other materials is to be…

Q: Using chaman- enskog compute the viscosity of argon at 1atm and 120 degree celcuis.

A: Given data: Pressure of argon = 1 atm Temperature = 120 0C

Q: Liquid-liquid extraction Is based on the differences in a. solubility c. partial pressure b.…

A: The answer is : (a) solubility

Q: Analyze the following images. Identify the type(s) of corrosion. Clearly state your assumptions.…

A: By seeing this image, we can infer that this is an image of a switchboard and by the use of screws…

Q: Only part b and liquid density is 0.588 g.cm-3

A: (b)   Temperature of 1-butene, T = 120°C = 393.15 K Pressure of 1-butene, P = 34 bar…

Q: Briefly describe the theory of absorption spectroscopy including the diagram of radiation source…

A: Absorption spectroscopy relates to a group of spectroscopic  methods used to measure the absorption…

Q: (SBR/NR)

A:

Q: For multi-component systems, Underwood Equations gives OL Minimum Trays O II Minimum Strip O II…

A: Distillation is a separation process in which light hydrocarbon is separated from heavy hydrocarbon…

Q: Does the hardness of a sample of water remains same if we take 1 liter of that sample or 10 liters ?…

A: The hardness of a sample of water is defined as the amount of dissolved calcium and magnesium in the…

Q: Because intermolecular forces can only be controlled at surfaces & interfaces. Because of the high…

A:

Q: Explain how molecular weight of a polymer can be determined by dilute viscosity measurements? Give…

A: Viscosity is a property of fluid by which measures a fluid's resistance to flow. It also describes…

Q: A solution is made by putting 100 g of NaNO3 into 200 mL of water at 70 degrees C.If the solution…

A: Answer Salt precipitates out is NIL A solution is made by putting 100 g of NaNO3 into 200 mL of…

Q: What if the amount of air is not stated? How can we assume for that? Is there any technique?

A: Given that :amount of air (assume 79mol% N2, 21mol% O2) is given

Q: How to find the density and viscosity of Air given 25 celcius, using perry's handbook? indicate what…

A:

Q: 4. What types of materials would have a yield point? 5. What is the difference between proportional…

A:

Q: 1. Determine the specific enthalpy of water for steam at 10.5 bars absolute pressure in bars.

A: As we know from the saturated water and steam table the value comes out to be or directly taken from…

Q: Q/ explain about effect wettability on 1- Saturation 2- Porosity 3- Relative permeability 4-…

A: To Explain The effect of wettability on saturation, porosity, relative permeability and capillary…