Please avoid rounding välu during the course of solution proper as much as possible. Write the final answer in 4 decimal places 9. A rectangular concrete beam 329 mm wide and 434 mm deep is simply supported over a span of 10.41m. The beam is reinforced with straight tendons situated 66 mm above the bottom of the beam under a prestressing force of 556 kN. Concrete weighs 22.66 kN/m^3 with modulus of elasticity Ec = 16,016.36 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads.

Please avoid rounding välu during the course of solution proper as much as possible. Write the final answer in 4 decimal places 9. A rectangular concrete beam 329 mm wide and 434 mm deep is simply supported over a span of 10.41m. The beam is reinforced with straight tendons situated 66 mm above the bottom of the beam under a prestressing force of 556 kN. Concrete weighs 22.66 kN/m^3 with modulus of elasticity Ec = 16,016.36 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use transformed area method. Determine a. Steel flexural stress (fs) b. Concrete flexural stress (fc) C. Concrete Compressive force (C) 20 kN/m (including beam weight) 8 m n=9 4 # 36 300 mm 420 mm 500 mm 80 mm
Use transformed sec method please
Please solve quickly, guess material
Question A prestressed concrete rectangular beam has area of cross-seciton equal to 36000mm² and moment of inertia of 2.7 x 108 mm4. A prestressing force of 195 kN is applied by tendons at an eccentricity of 55 mm from neutral axis. The loss of stress in steel due to creep of concrete is N/mm². [Take E = 2 × 105 N/mm², Ec = 3 x 105 N/mm² and creep coefficient = 1.50]
2. A 300 mm x 400 mm concrete beam has a span of 5.5m. A post tension force of 600 kN was applied at a point 60mm above the bottom of the beam. Assume concrete would not crack in tension. f.=20.7MPA. Unit weight of concrete is 23.5 kN/m3. Compute the following: а. Deflection due to prestressing force of 600 kN. b. Net deflection of the beam immediately after transfer. 60mm 5.5m
A rectangular concrete beam 277 mm wide and 495 mm deep is simply supported over a span of 8.37 m. the beam is reinforced with straight tendons situated 59 mm above the bottom of the beam under a prestressing force of 387 kN. Concrete weighs 23.36 kN/m3 with modulus of elasticity Ec=13,814.76 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 4 decimal places
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
A 6m long simply supported reinforced concrete beam has a width of 350mm and an overal1 depth of 470mm. The beans is reinforced with 2-28mm compression bars and 4-28mm tension bars, each located 70mm from the extreme fibers. Concrete strength f'c = 20. 7 MPa, and steel yield strength fy=415 MPa. Determine the ff: 1) Depth of compression block assuming both tension and compression steel yields. 2) what is the ultimate moment capacity of the beam in KN.m. 3) Determine the additional concentrated live load that can be applied at midspan if the dead load including the weight of the beam is 20KN/m. Use Mu=1.2Mdl+1.6M11 (Based of NSCP 2015) Show complete solution and neat handwriting. Use NSCP 2015.
Strength of materials, need help.
Please show complete solution in this problem pls. Need it asap. Thank you.
For a simply supported prestressed concrete beam, compute the stress in the top fiber at the centerline. Properties of the beam are: Width of the beam, b: 222 mm; Depth of the beam, d: 396 mm; Eccentricity of the beam, e: 177 mm; Prestressing Force, P: 541 KN; Superimposed Load, w: 8 KN/m; Length of the beam, L: 11 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) 000
The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. The column is subjected to an axial force of P=210 kip. Each rod has a diameter of 1 in.in. For A992 steel, Est=29.0(103)ksi, and for high-strength concrete, Ec=4.20(103)ksi. Determine the average normal stress in the concrete and in each rod. (Please type answer no write by hend)