Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN

Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) (2) Answer: Pmax i kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 7…

A: Diameter of tie rod (1) = 7 mmDiameter of pin B = 5 mmLengths:a = 670 mmb = 335 mmh = 370 mmAngle=to…

Q: Q7-Q8: A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of…

A: Longitudinal Stress, σlong = σx = 15 ksi. Tangential Stress, σtang = σy = 45 ksi.

Q: The one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile…

A: Cross section of the bar,Hollow square tube, a=10.47 inchthickness, t=1.47 inchtensile stress on…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum…

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm. The…

Q: 3. Compute the shear stresses. At the top of the side wall the thickness, 1, is 24 in. The torsional…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

Q: A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the…

A: Given: Pressure, P = 40 Mpa Inner diameter, d = 0.3 m Maximum tensile stress, σu = 646 Mpa Factor of…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: 1)In a thin plate, the state of stress prevails according to the figure. Calculate the principal…

A: Only one question is allowed to solve as per the guidelines.

Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…

Q: Given that, h = [0.1a] m, P = [10a] kN, -4 2 A1 =A2 =A3=2x10 m, E1=E2=E3=2x105…

A: Given data as per the question A1 =A2 =A3=2x10-4 m2 P = [10a] kN, E1=E2=E3=2×105 Mpa α = 300…

Q: Assume that the axial load P = 40KN applied to the lap joint is distributed equally among the three…

Q: An angled strut b = 6.2 in. thick is subjected to a force F = 55 kip and a uniformly distributed…

A: The values are F=55 kipq=23.5 kip/ft The thickness is b=6.2 in To find out:- The principal…

Q: Find bearing stress in the Revit connection of 15 mm diameter, if the applied load (P= 15 kN), the…

A: Given Revit diameter =15mm Applied force =15kn Thickness of plate= 20 mm We have to determine the…

Q: {5} If P = 100 kN for the bracket shown in the Figure, compute the maximum tensile and compressive…

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 10
mm and an allowable normal stress of 70 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 8 mm, and an allowable
normal stress of 170 MPa. Assume x1 = 2.9 m, x2 = 1.9 m, and y1 = 4.3 m. Determine the maximum load Pmax that can be supported by
the structure without exceeding either allowable normal stress.
B
(1)
(2)
Answer: Pmax
i
kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Using the same figure from item number one, find the largest safe value of P if the allowable stresses are 125 MPa for steel, 70 MPa for Aluminum, and 110 MPa for bronze. All applied loads are still axial forces and the materials are still rigidly connected. Bronze Aluminum Steel A=400 mm2 A=600 mm2 A= 300 mm2 2P ЗР 4P -3m -5m- -4 m
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 570 mm, b = 285 mm, h = 360 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 120 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h B a Answer: Pmax i b kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 9 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 5 mm in diameter. Assume a = 500 mm, b = 250 mm, h = 330 mm, and 0= 65°. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 130 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax (1) a i ● 1.418 B ● ● b kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 7 mm in diameter. Assume a = 560 mm, b = 280 mm, h = 450 mm, and 0= 70%. If the normal stress in tie rod (1) cannot exceed 200 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a Answer: Pmax= i B KN
Find the tensile stress in MPa in member AB shown in the figure All connection bars have a square cross section and the bar width is 15 mm. Points A, B and C are pin connections. Square 15 mm side 6m 3.5m C. D. 20KN
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 390 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 180 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a P i Answer: Pmax B b KN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= (1) i B b C /9 KN h P
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 9 mm in diameter. Assume a = 590 mm, b = 295 mm, h = 360 mm, and 0= 60°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 140 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) h a ● b
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 330 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= i B kN h