Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 65 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 8 mm, and an allowable normal stress of 175 MPa. Assume x₁ = 2.7 m, x₂ = 1.8 m, and y₁ = 4.1 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) Answer: Pmax = i kN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 10 mm and an allowable normal stress of 65 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 8 mm, and an allowable normal stress of 175 MPa. Assume x₁ = 2.7 m, x₂ = 1.8 m, and y₁ = 4.1 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) Answer: Pmax = i kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please show me the steps so I am able to practice thank you
Show Free Body Diagram Show complete solution anf clear hand writing
Show complete solution
Pls skip if not familiar and kindy use free body diagram for better understanding. Thank you!
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft (D= 2.25" and d=0.90''). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12x106 psi, 4x106 psi, and 6x106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft.
For the following problem please show intermediate steps including free body diagrams, equation used, problem setup etc. so that your approach can be followed. Finally please put the answer in a box with the appropriate unit.
- GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - PLEASE BASE YOUR SOLUTIONS ON THE SAMPLE PROBLEM I'VE GIVEN.
Please answer correctly. Please I need this ASAP. thank you Note: The tolerance is ± 1 in the third significant digit
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! Answer ASAP!
Please solve it within 30 minutes please i need help formulas are also attached
TORSION The UNITS OF FINAL ANSWERS are indicated in the questions, thua no need to encode units. However please provide the UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Please DO NOT USE SCIENTIFIC NOTATION in your final answera. A steel shaft with a diameter 51 mm and length 1.40m transmits 63.50 kW from an electric motor to a compressor.The allowable shear stress is 58.75 MPa and the allowable angle of twist is 2.2degrees. G-83 x 10^3 psi Determine the polar moment of inertia (in mm 4) of the steel shaft. Please DO NOT USE SCIENTIFIC NOTATION in your fina answers Please wrice Tinal answers ro 2 decimal places.) 664172.0551 mm4