Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 160 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 5 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 3.3 m, x₂ = 2.4 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) P KN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 160 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 5 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 3.3 m, x₂ = 2.4 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) P KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Required information Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Given: P=7 kips. A 30 in. -1.25 in. В 12 kips 25 in. 0.75 in. Find the average normal stress at the midsection of rod BC. The average normal stress at the midsection of rod BC is ksi.
Problem 3.1. A 1-in-diameter solid bar (), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), cuch supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)lf the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, e, of the tubular member? I in. 1=0.2 in. (1) (3)
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=66, T2 =11, T3 =26
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
The copper pipe has an outer diameter of 2.50 in and an inner diameter of 2.21 in . It is tightly secured to the wall at C and three torques are applied to it as shown in the figure below. Determine the shear stress developed at point A and point B. This point lies on the pipes outer surface.
The d-14-mm-diameter solid rod passes through a D- 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a- 28 mm, and the head has a thickness of t- 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 105 MPa, and the bearing stress between the rod head and the support plate cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D Rod Неad Answer in kN with 2 decimal places
A solid 2.20 in. diameter shaft is subjected to a torque of T = 365 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 i = Tmax in-plane A i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
10. An Assembly shown below whereas a link BD consists of a bar with 1 in. wide and 1/2 in. thick. Considering that each pin has a 3/8 -in. diameter, Find the maximum value of the average normal stress in link BD given the conditions: (a) O = 0, (b) 0 = 900. 4 kips .6 in. 12 in. 30° D
The lower end of the three bars in the figure are at the same level before the rigid homogeneous 18 Mg block is Each steel bar has an area of 600 mm2 and E=200 GPa. For the bronze bar, the area is 900 mm2 and E=83 GPa. a.) Compute the stress developed in the bronze bar. b.) Compute the stress developed in the steel bar and c.)Compute the elongation of the bars.
The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 700 lb/ft. Two concentrated loads also act on the rod: P = 2100 lb and Q = 600 lb. Assume a = 12 in. andb= 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in. w -> A C a b Answer: Ox-8in. = i psi Ox-24in. = i psi