Part BFind the steady-state expression for io (at the frequency found in the previous part) if ug-30 cos wt V. Suppose that io lo cos(ut +).where -180° << 180°. Determine the values Io. w, andin radians per second, andExpress your answers using three significant figures separated by commas. Express Io in milliamperes,in degrees.| ΑΣΦIo. w. 60, 10,0SubmitIvec 4 →Previous Answers Request Answer* Incorrect; Try Again; 4 attempts remaining?mA, rad/s, ° The frequency of the sinusoidal voltage source in the circuit in(Figure 1) is adjusted until the current i, is in phase withVg.Figure+1108150 ΩwwwioHE10 Ωwww4 mF<1 of 12 H

In this question, We need to determine the frequency of sinusoidal when current in the phase of…

Part B. Find the steady-state expression for io (at the frequency found in the previous part) if ug - 30 cos wt V. Suppose that folo cos(ut +). where -180° << 180°. Determine the values Io. w, and Express your answers using three significant figures separated by commas. Express Io in milliamperes, in radians per second, and in degrees. | ΑΣΦ. της ενός → O 1 ?

Part B. Find the steady-state expression for io (at the frequency found in the previous part) if ug - 30 cos wt V. Suppose that folo cos(ut +). where -180° << 180°. Determine the values Io. w, and Express your answers using three significant figures separated by commas. Express Io in milliamperes, in radians per second, and in degrees. | ΑΣΦ. της ενός → O 1 ?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
A non-sinusoidal voltage (e=20+15sin10o0t+ 10sin3000t+5sin4000t) Volt is applied to the circuit shown. Find the * ?total power iT 42 İL ic ET -J92 J4N
The source in the circuit shown is a sinusoidal source. The supply voltages across various elements are marked in the figure. The input voltage is: 3V- ww -14 V-10V moon It
A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin4000t) A is applied to the circuit shown. Find the total power? * 42 iL ww iT ic c -J92 J42 O 55 W 20 W 39 W O 28 W
A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin4000t) A is applied to the circuit shown. Find the total power? * İL iT ic -J92 J42 39 W 28 W 55 W 20 W
A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin400Ot) A is applied to the circuit shown. Find the total power? * İL www 1C iT -J9N J42 20 W 55 W 39 W 28 W
Problem 3 Compute the average and rms voltage of the waveform shown in the figure below. 6V - t 4 ms 4 ms 4 ms 4 ms -3 V
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
The maximum value of sinusoidal voltage is given by Vm= 1 V, What is the value of Peak to Peak voltage?
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
Please show your detailed solution Number 14 The current in a series inductive circuit is 7.5 A at 25 Hz. The circuit takes 425 W, and the power factor is 0.47. The resistance of the circuit is A. 7.32 ohms C. 7.98 ohms B. 7.86 ohms D. 7.56 ohms