Part A Morse Industrial manufactures the speed reducer shown in (Figure 1) A motor drives the gear shaft Swith an angular acceleration of a- (0.7e) rad/s, where t is in seconds. The radius of each gear is listed in the figure. Determine the angular velocity of shat E when t 5s after starting from rest. Note that gears C are fixed connected to the same shaft. Express your answer in radians per second to three significant figures. Figure ( 1 of 1 V AEd It vec rad/s A20mm Submit Previous Answers Reauest Answer 30mm -120mm X Incorrect: Try Again: 2 attempts remaining

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: X 300 mm D 800 mm B

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: The distributed load of w = (-2x² + 4x + 16) lb/ft acts on the beam as shown(Figure 1). Part A…

A:

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: Determine ly and ky.

A:

Q: 6 m

A:

Q: 13378.2898 lbm to lbf

A:

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: name these lines

A: The names of the given lines is given below.

Q: It is observed that the density of an ideal gas increases by 10 percent when compressed isothermally…

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: 11 The volume of a cube with sides of L is L. If the length is measured as 121 +2 mm, determine the…

A: Given data  The length measurement = 121+/-2 Find the worst possible error in the volume

Q: slove f

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…

Q: 2y dx

A: Solution given below.

Q: P= Р ар г? др RT ар - ? эт

A: The partial differentials .Given:The density is .