Water is drawn into the pump, such that the pressure at the inletA is -30 kPa and the pressure at B is 120 kPa The pipe has aconstant diameter of 100 mm Take h = 4 m.Part AIf the discharge at B is 0.25 m /s, determine the poweroutput of the pump. Neglect friction losses.Express your answer to three significant figures andinclude the appropriate units.

Answered: Image /qna-images/answer/f88046bf-069d-4d0b-9916-e3a15ba602e8.jpg

Answered: Part A If the discharge at B is 0.25 m…

Engineering

Mechanical Engineering

Part A If the discharge at B is 0.25 m /s, determine the power output of the pump. Neglect friction losses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Water flows through the 100- mm-diameter pipe at 0.035 m³/s. If the pressure at A is 475 kPa and the head loss between A and C is 1.5 m, determine the pressure at C. الشعبة -2 m الاسمن 100 mm 100 mm AB 30° Datu 4 m -2 m-
The water that is pumped into the system discharges into a tank that is weighed. It is found that 700 lb of water accumulates in 8.0 s. If the pressure at point A is 2.8 psi below atmospheric pressure. Determine the hp that the pump transmits to the water. Ignore the energy losses.
The diameter of a pipe at the section 1 and 2 are 10 cm and 15 cm respectively. Find the discharge through the pipe if the velocity of water flowing through the pipe at section 1 is 5m/sec. Determine the velocity at section 2.
QUESTION 2. Water is siphoned from the tank to the atmosphere as shown. Determine the discharge from the tank and the pressures at point (1). Neglect the losses and take the specific weight of the water as 9.806 kN/m3 (1) 4 m (2) ▼ 3 m 5 m + 0.15 m (3)
3. Consider the shown configuration where water Pump from a large, open reservoir flows through the pipe Water and discharges to atmosphere. When the pump is not running, it does not prevent water from flowing Pipe Spring through the pipe. At this state, the force that develops in the spring is 1000 N. However, when the pump is running, the force in the spring becomes 3000 N. The diameter of the pipe is 0.1 m. Neglecting all frictional effects, determine the power delivered by the pump to the fluid. Pwater 1000 kg/m³.
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
Q8) A fountain ejects water through a nozzle, which have inner diameters of 0.3 mm, at B as shown. If the volumetric flow rate into the 40-mm-diameter pipe at A and through the nozzle at B is (Q = 2 1/s) and the head losses between A and B is (hl = 3m), determine the height h of the water stream passing through the nozzle and the pressure at A. D A
A lawn sprinkler can be used as a simple turbine. As shownin Fig. , flow enters normal to the paper in the centerand splits evenly into Q/2 and Vrel leaving each nozzle. Thearms rotate at angular velocity ω and do work on a shaft.Draw the velocity diagram for this turbine. Neglecting friction,find an expression for the power delivered to the shaft.Find the rotation rate for which the power is a maximum.
D. The water is flowing through a tapering pipe having cross section areas 0.2 m2 and 0.1 m2 at sections (1) and (2) respectively. The discharge through the pipe is 0.2m3/sec. The section (1) is 0.2 m above datum and section 2 on the datum line. If the intensity of pressure at section (1) is 1962 kN /m2, the intensity of pressure at section (2) is one of the following (Solve and choose the correct solution). *
Determine the value of h in the siphon shown if velocity at C was 11.7 m/s. Diameter of the pipe is 2.5cm. Determine the pressure at point B
For the frictionless syphon shown, determine the discharge and the pressure heads at A and B. Consider a pipe diameter of 210 mm with the nozzle at the exit having 140 mm diameter. Consider a datum plane that is 0.16 meters above point A. 2.44 m 1.22 m 0.15 m
(12 mins) The penstock supplies water from a reservoir to the Pelton wheel with a gross head of 516 m. One third of the gross head is lost in friction in the penstock. The rate of flow of water through the nozzle fitted at the end of the penstock is 1.8 m³/s. The angle of deflection of the jet is 165º. Determine the power (MW) given by the water to the runner. Take speed ratio = 0.45 and C₁ = 1.0. Use p = 998 kg/m³. Round off your final answer to two decimal places.