Part A Determine the magnitude of the projected parallel component of the force F to pipe segment AB?

Q: Q1; Find the resultant of forces 5 kN F2 = 20 kN F3 = 15 kN 00

A:

Q: Determine the internal shear force at point D in the simply supported beam. Point D is located just…

A:

Q: 6m 180 kN 120 kN- 6 m D 4 -1.5 m Using the method of join, determine the forces on each joint and…

A: A truss is given, we need to find the force in members using method of joints.

Q: M a C a = 1.65m, b 3.2m, e 2.4m %3D F=210KN, M = 300KN - m(CCW), w 5.9KN/m %3D For the beam with…

A: Consider the free body diagram of the beam shown below.

Q: Given the simply supported beam below, and using the method of sections: 18 A t 1.5m C! 1.5m 1.5m KN…

A: Given:Required:Internal normal force at point D

Q: Referring to Figure Q1(a) until Figure Q1(e); (i) Check the stability and the determinacy of the…

A: "Since you have asked multiple question we will solve the first (B) for you. For other questions to…

Q: 2. The simple beam is subjected to loadings: w= 100 kN/m, F= 500 kN, M= 5000 kN-m. The lengths are:…

A:

Q: 2-7. Determine the magnitude of the resultant force F2 = F + F2 and its direction measured…

A: To solve this part, We need to resolve both the forces in the x and y direction Find the resultant…

Q: 1. find for placement reactions, inner forces, diagrams 6KNM 24 KN 10 KN 3 4 2.

A:

Q: Solve the magnitude of the resultant force. Neglect the diameter of the post. | FIGURE b FB = 175 N…

A: Magnitude of resultant force

Q: Determine the moment of the forces P & Q applied to the truss around points C and D. 2 81 41 V ioo#…

A: The moment of the forces P and Q about C, MC can be written as: MC=Px×BC [CW] NOTE: Q passes through…

Q: Define the forces affecting to beam CDB when P = 600 N

A: The given data is shown below: P=600 N

Q: I5 Jo KN A Im 6 m 2.5m 2.5m

A: To determine the resultant of all the forces acting on the beam, we need to calculate the total…

Q: Q1. Figure 1 represents the truss system for a billboard. Point loads at joints D and E and dur to…

A: MF=0109.9×15+109.9×7.5-A8=0A=309.09kN ↑Fy=0309.09+Fy=0Fy=-309.09kN↓Fx=0-109.9-109.9+Fx=0Fx=219.8kN→…

Q: F = 600 N 4 m 4 m- 30 n.

A:

Q: Find the forces in members BC and DE. Use Method of Sections. В |2 m DI 6200 N |1.5 m E A 4.5 m 4.5…

A: Given truss:

Q: Determine the solution for the bar forces in the truss shown when P = 1 kip and x = 5 ft

A: We will calculate the forces by using equilibrium conditions at each joint respectively.

Q: 600 cm 600 12 KN 1 kN 400 3 kN 4 kN 400cm 400 300 600 cm 300

A:

Q: 20 950 N Resultant: 350 N F

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: 10 KN 10 KN B D A 2 m 2 m RAx 2m Rey RAx

A: Given beam:-

Q: 11 What is the shear force at support A? 15 kN AA 4,5 m 1,5 平

A: Draw the free-body diagram of the beam.

Q: Part III. Analyze the internal forces for the beams and columns related to nodes F, G and J using…

A: In the following solution I have find out the shear and moment for almost all the beam and column. I…

Q: If the beam is subjected to F1 = 42 kN and F2 = 31 kN. The maximum shear stress on the cross section…

A:

Q: w many sets of shear and bending moment equations are required to completely define the beam and…

A:

Q: Draw the shear and bending-moment diagrams for the beam and loading shown and determine the maximum…

A: A simply supported beam AB, hinged at A and roller supported at D, consists of an overhang portion…

Q: Replace the parallel force system acting on the plate by a resultant force and specify its location…

A: to find resultant and its location on x-z plane

Q: Determine is magnitude of force in member AB in kN.

A:

Q: Determine the largest load P that can be applied to the frame without causing either the AVERAGE…

A: member CBaverage normal stress=150MPashear stress=60MPacrossection:square of 25mm side

Q: 3. Determine the angle 0 for the connecting member A to the plate so that the resultant force of FA…

A:

Q: Analyze and determine all force members by hand calculations for the determinate structure. Once…

A:

Q: If P = 27.4 and M = 7.53, Determine the Shear Force at point B of the Beam shown. Pink Min koft B A…

A:

Q: Compute the vertical component of the resultant between blocks B1 and B2 considering uplift force.…

A: To Determine: The vertical component of the resultant between blocks B1 and B2.   Explanation: The…

Q: Determine the internal resisting forces and moments at a section passing through point C. 60 lb /ft…

A:

Q: With the given force F, determine the angle (acute angle) between the Force and the segment AB. Also…

A:

Q: F= 20 N , p-15N; H= 6N; K= 3N FIND IN COMPONENTS OF EACH FORCE Fx t Fy s THEN ZFx? ZFy? FIND THE…

A:

Q: Determine and draw the curves of the cohesive forces of the beams in the following questions.

A:

Planar Stresses