Part 2- ProblemsShow formulas and substitution.1. How much power is consumed by a 12-ohm toaster connected to 120 volts? {2pts}An electric heating element has a resistance of 16-ohms and is connected to a voltageof 120 volts. How much current flows through the circuit? {2pts}2.A 10-ohm lamp is operated from 120 volts. How much power would it consume ifconnected to 240 volts? {2pts}3.4.What is the resistance and tolerance of a resistor with red, yellow, brown, and silverbands? {2pts}5.Give the color bands for a 100-ohm resistor with a 2% tolerance. {2pts}besuPage 2 of 3ELTE108_Quiz 3A_7-31-18810-28-17 mlc

As per our policy, i have attempted 1 question Given V=120 voltsR=12 ohm Calculating power…

Answered: Part 2- Problems Show formulas and…

Part 2- Problems Show formulas and substitution. 1. How much power is consumed by a 12-ohm toaster connected to 120 volts?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A dimmer that is marked 1200 watts @ 120 volts is capable of safely carrying 50 amperes of current.…

A: Given:-Power Rating=1200W,Voltage=120V

Q: in short Explain any two protective devices in the substation

Q: It takes 293 Kilo-Joules of energy to bring a certain amount of cold water to boil. If the water…

Q: What motor is used in the washing machines? Explain in detail the construction and working of the…

A: which motor is used in the washing machines?

Q: Question 36 What size TW copper conductor should be used for the branch circuit? (Show all of your…

A: The term "ampacity" is a portmanteau for "ampere capacity," which is prescribed by national…

Q: where did you get the 746 watts?

A: Since, the power is given in hp.i.e., Po=40 hp

Q: Find the current that flows through the filament of a 400 watts flat iron connected to a 220 Volt…

Q: What is the amperage of 3 clothes dryers with nameplate wattage at 7500 and 240V?

A: According to the question we have to calculate the amperage of 3 clothes dryers. Given nameplate…

Q: Is 5222 watts power rated equipment work if it is connected to a wire size no.6? Let voltage source…

Q: Power consumed by an electrical equipment is 600 watts and voltage rating is 120 volts then find…

Q: If one branch of a 120- V power line is protected by a fuse of 20-A.Will the fuse carry 10-ohm load

A: Given: V=120 VR=10 Ω Rating of fuse, If=20 A

Q: If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load?

Q: Three identical resistances are connected in star to supply 400 volts. If the value of the line…

A: Solution: Given data Three identical resistances are connected in star, VL=400V, line current…

Q: 1. A toaster takes 10 A, from a 120 volts power line. How much power is added? 2. How much current…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Transcribed Image Text: A household electrical device with a capacity of 2800 watts, equipped with a…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: What color code designates a 12, 10% resistor? What color code designates a 1k Q, 5% resistor? What…

Q: Question 1 In the given circuit, if Vdb is 12 volts, what is the value of E in volts? 82 多309 多122…

A: We will apply KVL in outer loop to find battery voltage Vcd. Now we will find current in 30 ohms…

Q: 4 222 resisher is to be made of nichrome wire. If the availa ble wire is 32 in. in diameter, how…

A: By resistance formula we will find out length of needed nichrome wire for given resistance value .

Q: You are an electrician working in an industrial plant. The company is constructing a maintenance…

Q: Q1: Refer to the table below, find the connected load (note that; 18 lights are used and 8 sockets…

A: The solution can be achieved as follows.

Q: Questions A: 1. What happen if you only touch one test probe of the voltmeter to one end of a…

A: According to the question we have to discuss 1. What happens if you only touch one test probe of…

Q: Explain any 2 protective devices in the distribution system

A: The protective devices in distribution system consists of protective relays, fuses, lightening…

Q: 35. A 120-volt branch circuit supplies a resistive heating load of 10 amperes. The distance from the…

Q: Given: A single family dwelling with a floor area of 120 sq.m., 220 volts 2 wire line to ground, and…

A: Consider the given information, The floor area of the room is 120 sq.m. Lighting loads are : 8 lamps…

Q: Support the finding that workers face many electrical hazards on the job

A: Electrical Hazards on the job 1.Contact with live wire results in electric shock or burn 2.Exposed…

Q: To replace 1500 Q resistor in a radio by any number of 1000 Q resistor, which way they can be…

A: To replace 1500 ohm resistor we need 3 unit of 1000 ohm resistor first we will connect first two…

Q: When a stove element takes 15 A when connected to a 120 volt line. How long does it take to consume…

Q: 3. It takes 293 Kilo-Joules of energy to bring a certain amount of cold water to boil. If the water…

Q: You are an electrician working in an industrial plant. The company is constructing a maintenance…

Q: If an equipment bonding jumper is run external to a raceway, it must be less than _______ feet.

A: If an equipment bonding jumper is run external to a raceway , it must be less than 6 feet.

Q: Which is a non permanent way of building a circuit? O stripboard О РСВ O Thick-film O Breadboard

A: The strip board is the board that are used to make the permanent circuits, the board is used where a…

Q: A 20 HP motor load takes 80 amperes over a feeder line with 0.05-ohm resistance per conductor. If…

A: In this question we need to find a efficiency of the given system.

Q: What type of connection is used when three different circuits are connected to a single supply line…

A: The answer as given below:

Q: 1. In a wye connected circuit, if the line-to-line voltage is 346 volts. What is the line-to-…

A: Wye connection is also called as star connection.

Q: A heater with a resistance of 8 ohms is connected across the 120 volts power line. How much is the…

A: As per the Ohm's Law we can say V=IR Here in this problem R=8ohms V=120 volts To find: current or I…

Q: 1. Determine the current flow in a circuit with a resistance of 5 Ohms on a 120 and 240 Volts…

A: 1.Given

Q: Explain the working of the electrical equipment used in the substation

Q: 1. In your own opinion. What will happen if Electric Circuit Board hasn't been invented?

A: Circuit boards aren’t that important. If we couldn’t use them there are other ways to connect…

Q: Why are there two electrical system in the world, those are 220 volt- 50 Hz and 110 volt- 60 Hz?…

A: The choice of frequency was arbitrary. Initially there was no particular reason for the different…

Q: !===== Discussion Questions 1. How does energy meter differ from a watt meter? 2. What is the…

A: In this question we will write about energy meter related problems.... Note:- as per our guidelines…

Q: Q: why are there two electrical system in the world, those are 220 volt- 50 Hz and 110 volt- 60 Hz?…

A: The choice of frequency was arbitrary. Initially there was no particular reason for the different…

Q: Determine the power provided by the 20-volt source in the circuit below. Indicate if the 20-volt…

A: The given circuit is:

Q: A one watt 470-ohm resistor is connected to 24 volts. Is the resistor operating within its power…

A: A one watt 470-ohm resistor is connected to 24 volts. Is the resistor operating within its power…

Q: Determine the total current flow in a lamp having 220 volt current supply, a fan of 240 volt supply…

Q: . Part I of which article in the National Electrical Code provides general requirements for…

A: Correct option is ARTICLE 250

Q: ive elem

Q: Using 3 band color coding method, evaluate the following resistor: Color bands: Red Brown Yellow

A: For a 3 band color coded resistor, the color codes of the three bands are given as 1st Band: Red 2nd…

Q: A ____ situation occurs when an ohmmeter reads resistance through circuit components even after the…

A: Fill the blank, about the power situation occurs when an ohmmeter reads resistance through circuit…

Concept explainers

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.

Question

Part 2- Problems
Show formulas and substitution.
1. How much power is consumed by a 12-ohm toaster connected to 120 volts? {2pts}
An electric heating element has a resistance of 16-ohms and is connected to a voltage
of 120 volts. How much current flows through the circuit? {2pts}
2.
A 10-ohm lamp is operated from 120 volts. How much power would it consume if
connected to 240 volts? {2pts}
3.
4.
What is the resistance and tolerance of a resistor with red, yellow, brown, and silver
bands? {2pts}
5.
Give the color bands for a 100-ohm resistor with a 2% tolerance. {2pts}
besu
Page 2 of 3
ELTE108_Quiz 3A_7-31-188
10-28-17 mlc

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Plz answer this ASAP Two resistors 15 and 20 respectively are connected in parallel and then connected in series with a resistor 10 2. The resistor circuit is connected to the terminal voltage X Volts. X=110 volts A.)Make an electrical circuit B.)Calculate the current flowing through each resistor.
1-connect the circuit shown in figure (2). 2-set the D.C power supply V1 & V2 to 10 volts respectively. 3-measure the voltage across the branch ab & the current through this branch (1). 4-disconnect V1 & replace it by a short circuit. 5-measure the voltage across ab (V) & current through this branch (I'). 6-connect V1, disconnect V2 & replace it by a short circuit. 7-measure the voltage across ab (V)& current through this branch (I"). 8-replace V1 & V2 by a.c. voltage source & repeat steps 2 to 7. R1 R2 v1 R3 v2 b R1=R3=4K R2=8k Figure (2) V1=V2=10v
Two heating units A and B are connected parallel across a 240-volt supply. Unit B takes thrre-times as much power in A, and the total power is 2400 Watts. Determine resistances of A and B.
Short circuit is occurred when: Select one: a. The voltage between the two terminals is zero although there may be a nonzero current between the terminals. b. All of the given answers. c. There will be a zero-resistance connection between terminal A and B and therefore the 2 terminals are at the same voltage. d. A pair of terminals connected by a wire (of zero resistance).
A 12-ohm resistor is connected in parallel with a series combination of 8-ohmand 16-ohm resistors. If the voltage across the 8-ohm resistor is 48-volts,calculate the (a) total resistance, (b) total supply voltage, and (c) circuit current.
Two heating units A and B are connected parallel across a 120-volt supply. Unit B takes twice as much power in A, and the total power is 2160 Watts. Determine resistances of A and B.
Answer the ff: 1. What are Voltage, Amperage, and resistance? 2. What is the difference between power and energy? 3. What is the difference between series and parallel circuits? 4. Determine the current flow in a circuit with a resistance of 5 Ohms on a 120 and 240 Volts current supply. (Circuit refers to the electrical wiring installation). 5. A circuit has a resistance of 20 Ohms, and the current flows at 12 Amperes. Determine the Voltage. 6. A water heater draws 10 Amperes at 240 Volts current supply. Determine its heat resistance.
Draw a set of 1.5-volt cells in a series circuit so that the total battery voltage is 9 volts. a) How many cells does it take? b) Show polarity connection. c) Suppose you connected one of the cells in part (a) so that it was backwards. What would the total voltage across the battery be? Why?
7. Draw soil resistivity change with seasons 8. Discuss the curves shown in the figure below. *** Below Some table that is very important for the grounding system. Table1. Earth resistance values Sr.No. Particulars Permissible values 1. Power Stations 0.5 Ohms EHT Substations 33KV Stations D/T centers Tower foot resistance 2. 1.0 Ohms 3. 2.0 Ohms 4. 5.0 Ohms 5. 10.0 Ohms
. What is the unit of measurement of resistance? O Volt ) Ohm O Ampere . How are pieces of equipment connected in parallel circuit? ) Give the current only one path to flow ) Give the current more than one path to flow s. What is grounding? ) One terminal is connected to the earth ) When resistance is zero
Figure 1, draw a two-loop circuit where the first voltage in series with first resistor to be connected at the supply side and the second voltage in series with second resistor to be connected at the load side. The three (3) resistors are connected in tee. Label the values of resistors and voltages. Complete the table below.
Two resistances of 10 and 15 ohms each respectively are connected in parallel. The two are then connected in series with a 5 ohm resistance. With 25 volts supply for the entire circuit. a. What is the equivalent resistance? b. Power at 15-ohm resistance.