Part 2: In a step-up converter, consider all the components to be ideal, Let Va be 8-16 V, V.-24 V (regulated), f-20 kHZ, Po ≥ 6 W. i). Calculate the minimum inductance L required to keep the converter operation in continuous-conduction mode under all conditions. ii). Specify the value of inductor for a maximum ripple of 3%. iii). Design a capacitor for part (i) and (ii) with a voltage ripple of less than 2%.

Part 2: In a step-up converter, consider all the components to be ideal, Let Va be 8-16 V, V.-24 V (regulated), f-20 kHZ, Po ≥ 6 W. i). Calculate the minimum inductance L required to keep the converter operation in continuous-conduction mode under all conditions. ii). Specify the value of inductor for a maximum ripple of 3%. iii). Design a capacitor for part (i) and (ii) with a voltage ripple of less than 2%.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ANSWER THE QUESTION
Example 3:-
A designer proposes a circuit that consists of a voltage regulator (sinusoidal) input signal, vin with a peak voltage of +20 V, as shown in Figure Q3(d). As an engineer in the same department, you are required to find the solution for the maximum and minimum peak of the output signal, vour when the diode is forward and reverse bias. Ideal y Vin ER Vout 5 VE Figure Q3(d)
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
(b) Discuss the impact of connecting a large capacitor filter across the load in Figure Q1(ii). Use appropriate waveform sketch to aid your discussion. + Vp - Us R2 RL Vs ( (i) (ii) Figure Q1. Single phase half bridge rectifier: (i) with a Thyristor (ii) with a Diode
Quiq
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
Q2) For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KO resistor) and the load current (through the load 2.2 KN resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode D1). The input Vi is sinusoidal with maximum amplitude (peak) of 14.1422 V and frequency of 60 Hz. The diode D1 is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
a. What is the effect of applying reverse voltage on a pn junction? b. What is the critical electric field and when will it happen?
1. Build the following circuit. Use the function generator to obtain the specified AC input voltage. D4 D1 + RL 1.2K + VsN D3 Y D2 9V sin(2n 50 t) Verify the amplı, 'de and frequency of the output waveform on the load resistor, RL. Peak voltage: Waveform period: Frequency 1.d) How much power would have. en dissipated on the diodes in total, if the same output waveform was obtainea sing a full-wave rectifier with a center- tapped transformer?
How does capacitance get created in a forward and reverse biased diode?Explain.