*P5.33. A voltage VL(t)=10 cos(2000TTt) is applied to a 100-mH inductance. Find the complex impedance of the inductance. Find the phasor voltage and current, and construct a phasor diagram. Write the current as a function of time. Sketch the voltage and current to scale versus time. State the phase relationship between the current and voltage.

Q: It is the Insulator used when the Transmission Lines' path need to take a turn on a sharp corner or…

A: Choose the correct option Which insulator is used to change path of transmission line or dead end.…

Q: This type of cable is a fabricated assembly of insulated  conductors enclosed in a flexible metal…

A: The metal sheath provides mechanical protection to the cable, making it more resistant to physical…

Q: 1-3. Given a 3-wire NPN inductive sensor, the black wire is to be connected to the ___________, the…

A: Inductive sensors are used to detect items without making physical contact. There are 2-wire and…

Q: When gauging the network's dependability, what measurements are most useful

A: We need to tell about measurements which are useful to gauging the network's dependability .

Q: EXERCISE 7.2.20 (a) Findiv(t) for t > 0 in the network shown below. 1 = 0 όμο 12V(+ ww 61 5 12 Ω ww…

A:

Q: 2. An actuator slowly extends as the push button is pressed. Upon the cylinder reaching a certain…

A: To draw the electrical as well as pneumatic circuit

Q: explain insulation coordination and write method of insulation coordination

A: We have to explain insulation coordination and write method of insulation coordination.

Q: substation auxillaries

A: Transformer- A device that transfers the electrical energy between two electrical circuits which are…

Q: 1.Compare Latching and Holding Current Ratio                      note::::::::: only short answer…

A: Latching current is associated with turn-on process of SCR. Holding current is associated with…

Q: What is the meaning of the acronym, XLPE? A. EXTRA LOW POLYESTER EQUIPMENT B. CROSS-LINED POLYETHYL…

A: In this we will write about XLPE....

Q: 142-0701-801 RF / Coaxial Connector, SMA Coaxial, Straight Jack, Solder, 50 ohm, Beryllium Copper

A:

Q: Explain the major consideration required for a protective system.

A: In the power plant, the generator is one of the most expensive pieces of equipment; therefore,…

Q: Explain thevenin equivalent circuit for dummies?

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: What is a field control station involves? A: Power connection B: One or more network connections C:…

A: Field control station involves 1) Power connection 2) One or more network connections 3) Connection…

Q: O Explain rod electrodes type earth protection with diagram.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: - Explain briefly the basic ways adopted to execute a power security analysis.

A: The power security analysis  is executed in two ways; 1) Security assessment: - The previous gives…

Q: How does the shielding in a cable affect its performance, and in what situations is it essential to…

A: Shielding in cables plays a critical role in enhancing performance and ensuring signal integrity by…

Q: What are the ATEX requirements of the explosion protected equipment?

A: Understanding ATEX Requirements for Explosion-Protected EquipmentIn industrial environments where…

Q: 4. Write all the types of connectors use in optical fiber cable?

A: The connectors mechanically couple and align the cores of fibers so light can pass.

Q: Name the type of wiring for the 3 wires proximity sensor shown below. BN Select one: O a. NPN…

A:

Q: What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given…

A:

Q: Amprobe Clamp-On Meter (Model RS-3) How many conductors should be in the jaws of the meter when…

A: Only one individual question is to be answered. So, kindly repost the remaining questions. 1. The…

Q: What is the control? O Conducts the current round the circuit • Regulates the current round the…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: Refer to the exhibit. In which section of the motherboard would a SATA cable would be installed? D…

A: SATA ports on the motherboard are commonly positioned away from all of the other ports. SATA ports…

Q: what are the three types of conduit that can be bent with a hand bender? list code article…

A: Hand benders are the most basic in design and have evolved little throughout the years. It's…

Q: Fiber cable sheath is removed by a. Wire Stripper b. Jacket Stripper c. Miller Stripper d. Round…

A: The solution is given  Answer is option b

Q: What is the approximate voltage amplitude and frequency of the waveform below? Trig Vertical Pos…

A:

Q: where is it most convenient to find a PKES system

A: We need to tell about PKES .

Q: What makes the knowledge of how to read a blueprint so important?

A: Blueprint is the drawing explains ovarall details of the component. It is nothing but a plan A…

Q: I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards…

A: According to the question we need to design a wooden train that runs on wooden track.What's the…

Q: What size outlet box is required for one 12/2 W/G NM cable that terminates on a switch, one 12/3 W/G…

A: To determine the required size of the outlet box, we need to consider the volume of the conductors,…

Q: What is the branch circuit protective device?

A: Branch circuit protective device is used to protect the motor winding and insulation if due to some…

Q: Using whatever reference you have, find an application of a diac and explain the network behavior.…

A:

Q: List 6 tools used in troubleshooting fibre optic links

A: Fiber optic links -  A fiber-optic link is often part of an optical fiber communications network…

Q: Explain the procedure to handle the "cast resign

A: In these units, coils are enveloped in resign by process of moulding. The transformer coils are…

Q: B/ Explain with the aid of drawing and equations the method of square low device carrier recovery

A: The Carrier recovery for the purpose of coherent demodulation, a carrier recovery system is a…

Q: In CRO, the voltage to be plotted is applied across ?

A: Given that  In CRO, the voltage to be plotted is applied across

Q: What is RG rating of coaxial cable? Give detailed answer please

A:

Q: choose the correct answer In solar power plant, the cost of concentrating collector is more than…

A: Solar collector: It absorbs the incident solar rays or radiation and converts them to heat energy…

Q: Give the other names of depletion region? (At least Two)

A: At the junction of p-type semiconductor and n-type semiconductor, in which there  is neither an…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.