OVERHEAD LOADER

Q: 3. Find the axial forces on members FH, FI, GI and HI. (Use any method) 40 kN 40 kN 40 kN H Upload…

A:

Q: Find the degree of freedom, number of links, number of joints, numbers of higher pair and determine…

A: Here we are find the Number of link and Higher pair and degree of freedom

Q: . Solve for the magnitudes of the vertical and horizontal forces on each joint using all the…

A:

Q: Draw a free body diagram

A:

Q: 4 HUN É. Determin by the driven pulley due to ctep the right and slack stdes of The be be 0.8 Nimm…

A:

Q: et

A:

Q: Draw a frame diagram to show their arrangement qualitatively, and solve for "T.

A: Solution

Q: The wall-crane structure shown in the diagram carries the 25 kN load.

A:

Q: Only do the FREE BODY DIAGRAM. NO NEED FOR SOLUTION. MAKE SURE THE FBD IS COMPLETE AND READABLE TO…

A: To Find : free body diagram of given footbridge

Q: Use method of joint to solve for the force reactions at members BC and AC Use method of section to…

A:

Q: One flange is attached to four 5x8 grade and M16 bolt connections with a total preload force of…

A: Write the diameter of the M16 bolt.   D=16 mm=16 mm×1 m1000 mm=0.016 m   Write the developed…

Q: cause failure of the link by buckling.

A: Given that cross section of BD = 30mm x 30mm Modulus of elasticity of the bar material = E = 200 GPa…

Q: 100 kN 100 kN 2 m 3 m 50 kN 2 m 6 m 6 m

A:

Q: Draw a free body diagram of part AD and part DCB. Show all detail. The compound is supported by a…

A:

Q: 13-10. Solve for the algebraic sum of the moments about the center of the axle shown in Figure…

A:

Q: draw free body diagrams for each

A: Free body diagram A free-body diagram shows the forces acted upon the body. It is a special example…

Q: Part C: For three elements (of your choosing), use either the Method of Joints or the Method of…

A:

Q: Universal joint is used for non parallel shafts whose axes are O coplanar. connecting radiator…

A: Universal joint: The universal joint is a joint between two rotating shafts which allows to move the…

Q: Find out degree of freedom ?number of link ,joint, must be indicted like as link symbol L and Joint…

A: Given: To determine: no of joints No of link DOF

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: a crank-slider linkage with the link lengths L2 10 mm, L3 = b = 120 mm, offset = c = тт. = 60° find…

A:

Q: 3. 4 Make kinematic sketch, describe the types of all the links and joints, and determine the degree…

A: The greatest number of logically independent values, or values with the ability to fluctuate, in a…

Q: Solve the following system of equations for forces BC and

A:

Q: - C -- B A Which point is necking starts А. B C. D D. A B.

A: In a stress strain curve ultimate tensile stress is the point at which maximum stress generated in a…

Q: length of the link PQ?

A: Given: A four bar mechanism is shown in figure:Where,   QR=600 mm   RS=300 mm   PS=400 mmSo,…

Q: proper key for the joint shown in figure E rque of T= 180 N.m. The hub has length of

A: Given data shaft dia = 30 mm length of hub = 50 mm allowable compressive stress = 120 MPa Required =…

Q: Corpo DCL Incompleto mg Cabo flexível

A: given:

Q: Use the method of joints to find the force in members HP and TU. Indicate whether the forces are in…

A: givenDETERMINE -force in members HP and TU USING METHOD OF JOINT

Q: Problems 1-4: Determine the support reactions of the members shown 1000 lb 400 lb/ft A 5 ft 5 ft-…

A:

Q: Using the method of joints, calculate the axial force in each of the bars 1,2,3, & 4 and state…

A: Given data  Given truss system

Q: For instability, at least one joint of the structure should be able to displace without causing…

A: Given: For instability, at least one joint of the structure should be able to displace without…

Q: Make an illustration for this problem and label it completely. This lever has a fulcrum that they…

A:

Q: 13-12. Figure P13.12 shows a mechanism that is used to shear thin-gauge sheet metal. If a 200-N…

A: Given DataF=200NHere the free body diagram

Q: Find the angle of contact on the small pulley for a belt drive with center distance of 75 in. if…

A: Center distance, C=75 in Larger pulley diameter, D= 18 in Smaller pulley diameter, d= 9 in

Q: pulley I =10mr? rigid, massless link. 3m

A: Given,

Q: Determine the reactions created by points A and E. Point A is a fixed connection and point E is an…

A:

Q: Compute the joint torques when the robotic manipulator picks up an object that weighs 10kg.

A:

Q: Draw FBD and solve for static equilibrium

A: For solution refer below images.

Q: Find the force by using method of joints. Determine wether it is tension or compression

A: Calculate the reaction at the support, Since there is no support showing the truss. let us assume…

Q: Use Method of Joints to find the forces in members AB, AC, BC, BD, CD, CE, DE, DF & EF

A:

Q: Link BD consists of a single bar 1 in, wide and in. thick. Each pin has a -in diameter and P 8 kips.…

A:

Q: Determine the number of pin joints 4. Which of the following has multiple degrees of freedom? OOO

A:

Q: problem

A: Given:S=6000lb/in2=864000lb/ft2W=490 ln/ft2A=2 in2=.0139 ft2L=1000ft…

Q: If deep groove ball bearings are to be selected, determine the basic dynamic load (C) and choose…

A: In the given problem, bearing selection is made based upon the dynamic load rating i.e., C.  For…

Q: a. What is the vertical component of the hinge reaction in lb? b .What is the horizontal component…

A: Write the given data with suitable variables. L=15 ftwo=45 lb/ft

Q: For the same question what stiffness k needed so the rod will stop smoothly on horizontal position 3

A: