Open notes, use f. 28 MPa, f,=420 MPa everywhere, except otherwise noted. Determine the design strength of a precast T beam with b=400 mm, d-500 mm, hy=125 mm, h=625 mm, b= 1.2 m, using one-half poos. 1. Select the actual size of bar and number to be used, and appropriately sketch the section allowing for No.13 stirrups 2. Determine the design moment capacity of the beam.

Open notes, use f. 28 MPa, f,=420 MPa everywhere, except otherwise noted. Determine the design strength of a precast T beam with b=400 mm, d-500 mm, hy=125 mm, h=625 mm, b= 1.2 m, using one-half poos. 1. Select the actual size of bar and number to be used, and appropriately sketch the section allowing for No.13 stirrups 2. Determine the design moment capacity of the beam.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
Given a 10"X16" reinforced concrete beam section as shown. The main reinforcing rebars consist of two #6 (each #6 bar has a section area of 0.44 square inches). Concrete fc'=3000 psi. Rebar yield strength fy=60 ksi. What is the section's theoretical nominal bending moment capacity in ft-k? loll O A. 65.8 ft-k. OB. 57.0 ft-k. OC. 34.1 ft-k. OD. 29.7 fft-k. X²N 16"
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
Refer to the figure shown below. 350 Given are the following: fc 55 MPa fou 1,350 MPa Aps - 1.500 mnm2 fpy - 1,100 MPa Use bonded tendons as prestressed reinforcement. Determine the design monment capacity of the section. (kN-m)
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 27 kips, w = 2.8 kips/ft, LAB = 3.0 ft, Lec= 3.0 ft, and Lco = 16.4 ft. Determine the magnitude of the maximum bending stress in the beam. |C LCD LAB I LBC Answer: ksi Omax
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
28" I 28" 3,5 1 16" hf=3.5" beam span = 12 ft-k Mu= 700 16" ft 16" 5' bw=16" T-beam works. 3,5" 16" check if 8#9. for the * fé= 3000 psi NWC. As = 8 #9 Grade 60 steel.
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc = 5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. %3D D B LAB LBC LCD Answer: ksi Omax
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm