One-tenth kmol of carbon monoxide (CO) in a piston- cylinder assembly undergoes a process from p1 = 150 kPa, T1 = 300 K to p2 =500 kPa, T2 = 370 K. For the process, W = -300 kJ.Employing the ideal gas model, determine:(a) the heat transfer, in kJ.(b) the change in entropy, in kJ/K.

Given data, p1= 150 kPa. p2= 500 kPa T1= 300 K T2= 370 K W= -300kJ

Answered: One-tenth kmol of carbon monoxide (CO)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ammonia contained in a piston-cylinder assembly, initially saturated vapor at 0°F, undergoes an isothermal process during which its volume (a) doubles, (b) reduces by half. For each case, fix the final state by giving the quality or pressure, in lbf/in.², as appropriate. Locate the initial and final states on sketches of the p-v and T-v diagrams
Air within a piston–cylinder assembly, initially at 50 lbf/ in.2, 510°R, and a volume of 6 ft3, is compressed isentropically to a final volume of 0.5 ft3. Assuming the ideal gas model with k = 1.4 for the air, determine the: (a) mass, in lb. (b) final pressure, in lbf/in.2(c) final temperature, in °R.(d) work, in Btu.
A closed system consists of gas of 2 kg initially in state 1 with p1 4bar and specific volume V1 = 1m /kg. The system undergoes a power cycle consisting of the following processes: Process 1-2: polytropic process to v2 = 2m3 /kg, p2 = 1bar; Process 2-3: isobaric compression to v1; Process 3-1: isochoric process to p1. Draw the cycle on a p – v (specific volume) diagram. Show the system states, cycle direction, and the cycle (net) work.
13
Refrigerant 134a at p1 = 30 lbf/in2, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 350 Ib/h and exits as saturated vapor at p2 = 16O Ib/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 3.5 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr.°R.
13
P
Argon (molar mass 40 kg/kmol) compresses reversibly in an adiabatic system from 5 bar, 25 0C to a volume of 0.2 m3. If the initial volume occupied was 0.9 m3, calculate the work input in MJ to 3 decimal places. Assume nitrogen to be a perfect gas and take cv = 0.3122 k J / k g K.
Refrigerant 134a at p1 = 30 lbş/in?, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 250 lb/h and exits as saturated vapor at p2 = 160 lbę/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 2.5 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr-°R.
2 kg of air contained in a piston-cylinder assembly undergoes a process from the initial state of T₁ = 400K, v₁ = 0.5 m³ to the final state of T₂ = 600K, v₂ = 0.8 m³. Assume the ideal gas model with cv = 0.72 kJ/kg . K for the air. Kinetic and potential energy effects are negligible. - Can this process occur adiabatically? Demonstrate it with formulas and calculations. If yes, determine the work, in kJ, for an adiabatic process between these states. If not, determine the direction of the heat transfer (in or out of the system). Determine the temperature of the isentropic process with the same initial state, T₁ = 400K, v₁ = 0.5 m³, and the same final specific volume: v₂ = 0.8 m³.
Five kilograms of a two-phase liquid-vapor mixture of water initially at 300\deg C and x1 = 0.5 is heated from the initial state to a saturated vapor state while the volume remains constant. The process is brought about by heat transfer from a thermal reservoir at 380\deg C. The temperature of the water at the location where the heat transfer occurs is 380\deg C.Let To = 300 K, Po = 1 bar, and ignore the effects of motion and gravity.
Five lbs of propane is contained in a closed, rigid tank initially at 80 lbf/in.2, 50°F. Heat transfer occurs until the final temperature in the tank is 0°F. Kinetic and potential energy effects are negligible. Determine the amount of energy transfer by heat, in Btu. Q= i Btu

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

One-tenth kmol of carbon monoxide (CO) in a piston- cylinder assembly undergoes a process from p1 = 150 kPa, T1 = 300 K to p2 = 500 kPa, T2 = 370 K. For the process, W = -300 kJ. Employing the ideal gas model, determine: (a) the heat transfer, in kJ. (b) the change in entropy, in kJ/K.