On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall have no visible porosity that exceeds 1/32" O B. shall have no visible porosity that exceeds 3/32" O C. shall have no visible porosity O D. shall not have a sum of visible porosity that exceeds 3/8" O E. shall not have a sum of visible porosity that exceeds 1/2"

On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall have no visible porosity that exceeds 1/32" O B. shall have no visible porosity that exceeds 3/32" O C. shall have no visible porosity O D. shall not have a sum of visible porosity that exceeds 3/8" O E. shall not have a sum of visible porosity that exceeds 1/2"

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 38R: What two amounts must be multiplied to determine the weight of weld metal required to fill a groove...

See similar textbooks

Similar questions

What weld section properties are required to analyze the weld between the horizontal tube and the vertical I-beam? O a. A O b.I O c. J O d.J,A O e. A, J, I O f. I.J
a. Show how the extent of the surfacing weld is indicated between the vertical centerlines in the following illustration.
Sketch the groove welds specified and show all given weld dimensions
What would be the transverse shear strength per inch of weld if a specimen that was 2.5 in. wide withstood 25,000 lb?
QUESTION 19 Which of these welds could be analyzed using the AISC Code's "kips per inch" method? (Indicate all applicable.) A В C D E a. A 6. B O c. C O d. D e. E O O O O C
Millimeter 17. Which part of the marking gauge is used to mark lines on wood? To measure the ductility of weld metal b. To test the skill of a welder To perform a non-destructive test d. To approve welds to certain standards a. C. 18. Compressive stress can be defined or described 2s an internal force in a material resisting a. a pulling load. b. shearing load. pulling and shearing load. d. pushing.load. • C. 19. Which plane more suitable for further smoothing a planed surface? Router plane. b. Trying plane. c. Smoothing plane. a. 20. Which one of the following is gives the name of the screw? a. Siot. b. Thread. Head. d. Shank. C. 21. How to hold the hammer handle while driving the naii? Middle of the handle. * b. Anywhere in length of the handle. C. Near the hammer head of the handle. End of the handle a. USF ال لجنة العلمية d. File is
Find the information from the following weld symbol. 20 2.
15 What is the weight of the weldment shown? (MS) Plate= .2835 lbs. per cubic inch. S 58" x 21 x 21" M.S. plate both ends 5/8=-625 W16 x 26 x 14 12' a 26 lbs/ft a. 241.90 lbs b. 533.28 lbs. C. 206.45 lbs d. 455.14 lbs 7
SOTH SIDES A36 8. SPACER MATERIAL 90° BACKING MATERIAL 1 1 용x글 436 АЗ6 TO BE REMOVED 11. Apply the welding symbol to the following joint members to indicate an other side square groove weld with " root opening having a class 3 consumable insert located on the arrow side. Copyright © 2015 Cengage Learning 1/4 C.
Draw the welding symbol from the following information. SINGLE J BUTT WELD CONVEX FACE SIZE 5 mm HIDDEN SIDE SITE WELD A- BI II 123 ... GO
Radius of Mohr's circle representing the given state of stress ?
Q-The lap distance in different types of bonding is equal to the horizontal distance between two Perpend joint in the rows sequential and must be equal to half the width of the brick minus half width of the Perpend joint and the value was .. and it must be applied to prevent the continues of perpend joints in the sequential rows. five point five cm (5.50 cm) five point seven five cm (5.75 cm) Non of them five only (5.00 cm) five point two five cm (5.05 cm)