OTHE FORCEPAPPLIED TO THE SRAKEHANDLE ENA BLES THEBANDBRAKETO REDUCETHE ANGULAR TEEDROTATING DRUM,OFo.) IFP 390 N, DETERMINETHETENSION8IGGERBANDBRAKE.b.) If P. 346 N, DETERMINE THE JMALLERBAND BRAKE,TENGON ONc.) DETERMAINETHECORRESPON DINGVALUEOFTHEBRAKINGTORQUE AC TINGTHEORUM0.2mA=0.2R= 0.225m0.15m

Force P is applied to the brake handle to reduce the angular speed of the rotating drum μ = 0.2 It…

O THE FORCE APPLIED TO THE SRAKE HANDLE ENABLES THE BAND BRAKE TO REDUCE THE ANGULAR STEED ROTATING DRUM, OF 0) IF P 390 N, DETERMINE TENSION ON THE BIGGER BAND BRAKE. b.) If P. 340N, DETERMINE THE SMALLER TENGON ON BAND BRAKE C.) DE TERAMINE CORRESPON DING THE VALUE OF THE BRAKING TORQUE ACTING THE DRUM 0.2m H=0.2 R= 0.22 5m 0.15m

O THE FORCE APPLIED TO THE SRAKE HANDLE ENABLES THE BAND BRAKE TO REDUCE THE ANGULAR STEED ROTATING DRUM, OF 0) IF P 390 N, DETERMINE TENSION ON THE BIGGER BAND BRAKE. b.) If P. 340N, DETERMINE THE SMALLER TENGON ON BAND BRAKE C.) DE TERAMINE CORRESPON DING THE VALUE OF THE BRAKING TORQUE ACTING THE DRUM 0.2m H=0.2 R= 0.22 5m 0.15m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10ft A k 10ft etermine the vertical displacement of Joint C A = 0.5 in² > E = 29 * 10³ ksi F B 4K 10 Pt E 10 ft 4K
F 6KN O sm SOLVE Au FORCEN G N EACH MEMPER 0. 6m 0.2m 0.4m
Question 3 of 15 > -/5 View Policies Current Attempt in Progress The bell-crank mechanism is in equilibrium for an applied load of P = 30 kN. Assume that a = 300 mm, b = 245 mm, and 0 = 64°. Calculate the resultant force on pin B. (1) F1 Bell crank В B a Support bracket Answer: B = i kN
STRENGTH OF MATERIALS (Please answer ASAP. No long explanation needed.Thumbs up will be given) The compound shaft, consisting of a solid steel (diameter = 140 mm) segment and hollow aluminum ( outer diameter 120 mm, wall thickness = 10mm)) segment, carries the two torques shown. Determine the maximum permissible value of T subject to the following design conditions: τst ≤ 93 MPa, τAl ≤ 50 MPa, and θ ≤ 4o (angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminum. Include the FBD of each segment and show the internal torque. DISREGARD THE GIVEN DIAMETERS IN THE FIGURE.
Determine support reaction at roller support
For the beam below, determine the following, assume EI is constant. What is MBA in k-ft? O Select the correct response: C 108 -72 72 2 k/ft -180 24ft
Considering the effects of the prestressing forces (assume no loss) and the working loads (include the selfweight of the beam). Calculate the stress indicated below. Calculate fbot at the ends. (MPa), consider sign convention (- for compression, + for tension) SELEWEILHT 300 P P 300 kN 400 de= 24 m3 900 70
Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression.
- For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 15 kN, F₂ = 25 kN, F3 = 45 kN, F4 = 25 kN, and M = 110 kN-m. O 6 m H Your answer is partially correct. G Answers: 8 m F₂ B x-axis: x = i -11.4 y-axis: y = i 7.27 Equation of line: y = 0.636 M D F₁ F₂ m m X + i 7.27 m
T1
Q.2 Two circular 2T 2T T steel shafts AB and (A aluminunf steel steel CD with 40mm diameter is attached – 2x 2x and aluminum shaft BC with a 20mm diameter. The shaft is fixed at point A. Using the below values calculate the followings x= 1.2 (m) T= 6 (kN.m) Gst=75 GPa Ga=25 GPa a) Calculate internal Torque in AB, BC, and CD obeying the sign convention. b) Calculate angle of twist of C with respect to B c) Calculate angle of twist of D with respect to B d) Calculate maximum shear stresses in AB, BC and CD
If the clamping force at G is 900 N, determine the horizontal force F that must be applied perpendicular to the handle of the lever at E. The mean diameter and lead of both single square-threaded screws at C and D are 25 mm and5 mm, respectively. The coefficient of static friction is μs = 0.3.