Answered: O) Shunt PMMC was designed by using…

O) Shunt PMMC was designed by using indirect method to provide an ammeter with current range 5A, 10A, 20A. The internal resistance is 500 and full scale current of ImA. find Rb.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: A DC ring main ABCDA is fed from point A from a 250 V supply and the resistances (including both…

A: Given: RAB=0.02 ΩRBC=0.018 ΩRCD=0.025 ΩRDA=0.02 ΩIB=150 AIC=300 AID=250 AVA=250 V Write KCL at node…

Q: Find Rab. ba

A: The circuit is shown below: Using the star to delta transformation, the delta circuit is converted…

Q: 5. Via nodal analysis, obtain Vin the circuit below. Leave your answers in terms of the resistance…

A: In this we will find node voltage...

Q: Draw circuit of wilder current source.

A: The BJT are used as constant current source. The collector current of BJT is relatively independent…

Q: KIRCHOFFS CURRENT LAYW(WRITE THE EQUATIONS OF THE FOLLaNING FIGURES BELOW)

Q: A DC source has Thevenin's voltage of 70 V and Thevenin's resistance of 3.5 ohms. If the maximum…

Q: För the deple =hown below, VTN = -2V and %3D (*) Kn = 0.1 Assume VDD = L v2 5V, Rs = 5 ko then the…

Q: For the given figure, find the branch current i1, i2, i3, i4, i5 and i6 by any method of analysi

A: The above circuit can be solved using either of the circuit theory rules mentioned below:…

Q: 1 Ia = ?? A 2.ib= ?? A 3 Vx = ?? 4 power at Rx = ?? 5 power at Rb = ??

Q: Jse wye to delta transformation to obtain the equivalent resistance, in phms, at the terminals a-b.*

Q: 12. The resultant voltage of more than one EMF connected 'in-series' depends on the values of the…

A: The resultant voltage of more than one emf connected in series depends on the values of the…

Q: ical circuit that includes a voltage source an internal resistance rs and a load resis- is shown in…

A: Question 6 and 7 are not part of electrical engineering they are part of mathematics.....I will…

Q: R IRL RL PzM n the circuit using a Zener dibde above, given that V, v, R=25 ka, R6 A0, and the Zener…

A: Zener diode maintains Vz when voltage across zener diode is exceeds Vz. Use ohms law to find current…

Q: Using nodal analysis, node voltage

Q: 3. Determine the DC (currents, terminal voltages and inter-electrode voltages) parameters of the…

A: The solution is given below

Q: Consider designing an ammeter with a proper shunt resistance. In order to find such shunt, the…

Q: For the circuit shown below: Bpc = 100, VBE = 0.7V, V7 = 26 mV. 4. What is the Purpose of Re? 5.…

A: We need to find out bjt current and bjt small signal parameters .

Q: In the circuit below; if I12=2AZ30°, a) Vc voltage value =? b) L1 and I12 current =? c) Vs welding…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: I'm looking to note some key advantages and disadvantages of George Westinghouse AC current grid…

A: Here it has been asked to discuss the the main advantages and disadvantage of George Westinghouse AC…

Q: The devite shoun belou वर् valtagesource. s cam be. modeled by witha resistor in sories ती The table…

Q: N SUPPLYING A DC VOLTAGE TO CIRCUITS IN PROTEUS, THE NEGATIVE TERMINAL OF THE DC SUPPLY IS TO BE…

A: DC (Direct Current) Supply- DC supply is a one-dimensional current flow in the form of…

Q: 1. Sketch V and determine Vdc Vrms- 100Y 4.7 12 54 k Si 本

A: The question is from power electronics.

Q: a) Explain the construction of LVDT. Identify some suitable examples according to their…

A: As per bartleby guidelines for more than one question asked only first is to be answered please…

Q: With V,- 2= sinzt, find the value that of C will cause the maximum Powed in the load vesistence.…

Q: び oe 2. Find the oltage drope cach resiutor, 3. Find the remaining voltage each sidte , By using…

A: The solution is given below

Q: A single phase transformers working at UPF has an efficiency of 90% at both half load and at the…

Q: Suppose in a two-coil scenario, a positive increasing current driven in one coil results in a…

A: Note: Since you have posted multiple independent questions in the same request, we will solve the…

Q: Construction of wind farm is finalized on a site that has a steady wind at a speed of 9.5 m/s. Find…

Q: In an AC circuit, the load has a supply voltage of 240 cos(800πt + 60) volts and a current of…

Q: Q1) (Dc analysis) For the circuit above find the following: 1. Ica- 2. VCEQ. 3. lea. 4. VEQ- 5. IBQ-…

A: To solve above problem, one should know about DC analysis of BJT. DC analysis of transistor is done…

Q: 5. Via nodal analysis, obtain Vin the circuit below. Leave your answers in terms of the resistance…

A: In this question, Find the voltage V using the nodal analysis. Resistance R and Reactance X

Q: Find the equivalent circuit of Thévenin and later determine the current flowing on the load resistor…

A: We need to thevenin voltage and thevenin resistance across the load resistance, to calculate voltage…

Q: Find its potential difference and individual voltages such as Va, Vb,Vc and Vd using nodal analysis…

Q: Three impedances Z, -1-j4 ohms, Z2 - -j6 ohms and Z, 4 j3 ohms are connected in series- parallel. Z,…

Q: A 20-kVA, 507 V load is to be supplied by an ideal step-up autotransformer from a 400-V source. Find…

A: Neglecting the losses in transformer input power KVA = output KVA. VA=voltage×current.

Q: Q1: For the network of Figure below : a) Calculate ZT. b) Determine, IT In and I2. c) Find Vsn, V122…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subparts for…

Q: ) Wind farm consist of ten wind turbines with nominal capacity of 2MWper turbine, has a total of 20…

A: Capacity factor =Average load / installed capacity. Average load = no. Of units produced / no. Of…

Q: äbä 35 For the circuit shown below, find the current in each branch .by using Kirchhoff's Low 100…

A: Kirchoff's law:-the Kirchoff's law is basically of two types are Kirchoff's current law and…

Q: 2. Homework problem: Find the source voltage for the circuit shown in figure below, using current…

A: Circuit is given,

Q: 1/1 By using the experiment of series connection: if the R1=50ohm, R2=100ohm and R3=150ohm.. the…

Q: Investigate and expose 3 applications and their importance in everyday life (real life, home,…

Q: It is required to connect Aktif and capacitive reactive mechanical meters that will measure the…

Q: a. A simple DC circuit is shown in Figure 4. If ix=10A, find v1 and iy If v1=6V, find ix and iy. i.…

A: The solution can be achieved as follows.

Q: How can I find Vx through nodal analysis?

A: First we can do source transformation, current source of 5A is replaced by equivalent voltage source

Q: Use nodal analysis to solve for the voltage across 6 ohms resistor and current across 8 ohms…

Q: REF-SPP-COE-ECE-DEP-GCV-101-R00-09262 Seatwork No. 7 Find VTH, ZTH, and IN for the circuit shown…

A: In this question, We need to determine the Thevenin voltage and Thevenin impedance and Norton…

Q: Create an schematic diagram of the following circuit (open, short, parallel and series). Include…

Q: Q5(a) i) Explain the major difference between IT and TT earthing systems using sketches with labels.…

A: consider the given question;

Concept explainers

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.

Question

I need the answer as soon as possible

O) Shunt PMMC was designed by using indirect method to provide an
ammeter with current range 5A, 10A, 20A. The internal resistance is 500 and
full scale current of ImA, find Rb.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

complete the table and make a graph using SILICON DIODE. then explain how did you get the values and plot the forward and reverse biased
In a circuit that composed of a single diode that connects an AC source to a load. the diode acts as function of
2. Draw the graph of the voltage across the 10K resistor (calculate the values for the different voltages across the 10K resistor) of the circuit in the figure, knowing that the voltage source V is sinusoidal. And the diodes are silicon
5 For the following circuit: a) Draw a table to mention the names, the states (ON/OFF) and turn on voltages for all the diodes of the circuit. (V = 3.5V for D3) and draw the equivalent circuit. b) Find the voltage across R1, R2, R3 c) Find the current through D1 , Dz , D3 and D4 D1 Si R2 D2 5002 Si R1 7502 R3 D3 D4 V1 1kn Blue GaAs 10v
Find the values of I and V for this circuit, assuming that the diodes are ideal.
Analyze the circuit using KVL or superposition, Analyze the circuit assuming many source values that lead to all possible cases of diode states, re-plot the circuit and develop the relation between the output voltage and the source.
Find the value of the resistor R since Vr = 50 mv since the diodes are identical.
A circuit consist of a single diode and resistor which are connected to AC source. The resistance voltage is: O AC voltage with V=Vm/ O DC voltage with V= Vm/v2 O AC voltage + DC offset O only DC voltage with V=2Vm/
Using ideal diode model, the current I passing through the diode is equal to SKL I min si lov
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
use the constant voltage drop model in analyzing the diode circuit below: 10 92 V₁ (+ M 1 V D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF C B. D₁ is OFF and D₂ is ON - 1 V D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON + 1092 Vo
When resistors with higher wattage ratings are required, resistors are generally used to dissipate the excessive heat. a) Variable b) Fixed c) Wirewound d) Preset The diode is considered shorted when both anode and cathode has a) Low resistance b) High resistance c) Different resistance d) None of the above When two resistors are connected in parallel then their overall power rating is a) Increased b) Decreased c) Doubled d) Reduced