O Parallel paths increase the amount of resistance in the circuit, further limiting the current that can flow. O Each parallel connection adds a path for current to flow, increasing total current through the circuit. O Each parallel connection adds a path for current to flow, increasing the current through each path. O Parallel paths increase total current, which is the same as decreasing total resistance. O Each path will have a share of the total current until there is not enough left, so paths with the greatest resistance may not have any current th them at all. O Each parallel path will have a share of the total current through the circuit that is inversely proportional to that path's resistance, meaning the with least resistance will allow the most current and the path with greatest resistance will allow the least current. O Parallel paths always divide the current equally, reducing the total current through the circuit. O Parallel paths always divide the current proportionally, decreasing the total current through the circuit. 's resistance meaning the path with

O Parallel paths increase the amount of resistance in the circuit, further limiting the current that can flow. O Each parallel connection adds a path for current to flow, increasing total current through the circuit. O Each parallel connection adds a path for current to flow, increasing the current through each path. O Parallel paths increase total current, which is the same as decreasing total resistance. O Each path will have a share of the total current until there is not enough left, so paths with the greatest resistance may not have any current th them at all. O Each parallel path will have a share of the total current through the circuit that is inversely proportional to that path's resistance, meaning the with least resistance will allow the most current and the path with greatest resistance will allow the least current. O Parallel paths always divide the current equally, reducing the total current through the circuit. O Parallel paths always divide the current proportionally, decreasing the total current through the circuit. 's resistance meaning the path with

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter14: Troubleshooting Electric Control Devices

Section: Chapter Questions

Problem 32RQ

See similar textbooks

Similar questions

A 0 – 150 voltmeter has a resistance of 2000-ohms per volt. It is desired to change this voltmeter to a 0 – 600 volt instrument by the edition of an external multiplier. What is the resistance, in ohms, of this external multiplier?
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
5 batteries are connected in parallel to supply current to a load resistance for heating. Each battery consists of 12 cells in series. The emf per cell is 2V and the individual cell resistance is 0.15 ohms. What should be the resistance of the load so that the power consumed by the load is maximized? *
Theoretically determine the voltages across each of the resistors for the Experiment circuit using Kirchhoff's voltage law technique.
Draw a schematic of a circuit that converts the thermistor resistance to a measurable voltage. I suggest basing it on the only circuit you have studied so far: the voltage divider. Assuming that you have a negative-thermal coecient (NTC) thermistor and that you want higher temperature to result in higher voltage, which of the resistors in a voltage divider is the thermistor and which is a fixed resistor? Use the proper thermistor symbol and put the thermistor part number on the schematic. (For the final report, update this schematic with the resistor value chosen in the lab.)
A secondary cell having an end of 2v and internal resistance of 1amp is connected on series with a primary cell having an end of 1.5v and internal resistance of 100amp, the negative terminal of each cell being connected to the positive terminal of the other cell . A voltmeter having a resistance of 50amp is connected to measure the terminal voltage of the cells. Calculate the voltmeter reading and the current in each cell.
Explain what you know about the circuits in the figure
Consider a PV Module with 8 PV cells with the Size of each 10cm x 5cm are connected in series. Calculate the following for the above Module. Refer to the above PV Module choose the correct statement a. The output power of each PV cell is 0.5 W b. The output power of each PV cell is 0.75W c. The output power of each PV cell is 1W d. The output power of each PV cell is 0.25W
In the circuit, Determine: a. the total resistance (R7) of the circuit in kl. (. . places for the final answer) b. the current flowing in mA for each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the 12V final answer) c. the voltage in V across each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the ; use 2 decimal R = 3000 R3 = 4000 R2 = 1000 R4 = 1ka %3! final answer)
A circuit consist of three resistors with R1 20 resistance R2 30 and R3 50 and 125V battery connected and an emf source. Find out the (1) equivalent resistance, (2) the current across each resistor, (3) potential drop across each resistor and (4) the power dissipated in each resistor.
Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell
Using the black box from below, construct a circuit that fulfills the following objectives: Volage in point A: 500mV Voltage in point B: 1000mV