1 Us = -Vout RF/Rs' AvOL) RF/R$ ' AvOL). (8.18) O Consider an inverting amplifier with open-loop gain 105. With reference to equation 8.18: a. If Rs = 10 k2 and Rp = 1 M2, find the voltage gain Av(CL)- b. Repeat part a if Rs = 10 k2 and Rp = 10 M2. c. Repeat part a if R$ = 10 k2 and Rp = 100 M2. d. Using the resistor values of part c, find Av(CL) if AvOL) → 00.

1 Us = -Vout RF/Rs' AvOL) RF/R$ ' AvOL). (8.18) O Consider an inverting amplifier with open-loop gain 105. With reference to equation 8.18: a. If Rs = 10 k2 and Rp = 1 M2, find the voltage gain Av(CL)- b. Repeat part a if Rs = 10 k2 and Rp = 10 M2. c. Repeat part a if R$ = 10 k2 and Rp = 100 M2. d. Using the resistor values of part c, find Av(CL) if AvOL) → 00.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the AM modulated signal (assume sinusoidal signal modulating a sinusoidal carrier) in both time and frequency domain. Remember, graphs with missing labels and values will be graded with zero.
9.4. The signals in Figure P9.2 are zero except as shown. (a) For the signal x ln] of Figure P9.2(a), plot the following: () xl-n]ufn] (iii) xn}u[n + 2] (v) xn)oln - 21 x,[n]ul -n] (iv) x-njul-2 - n] (vi) x,ln|(8[n + 1] + 6ln - 1) (b) Repeat part (a) for the signal x,ln] of Figure P9.2(b). (e) Repeat part (a) for the signal xn] of Figure P9.2(c). (d) Repeat part (a) for the signal xfn] of Figure P9.2(d). -2-1' 101 2 3 456 (a) (b) ... 6-5-4-3-2-1, 01 23 4567 (d) Figure P9.2
impedance matching and tuning techniques, in microwave.
The gain of vertical deflection amplifier in CRT is 90. If an input signal of 110mV is applied, it will produce electrical field of 33V/cm and vertical deflection of electrons beam on the center of plates of 4.31x10-3 cm with an angular deflection given by arctan (0.0137). The electrons enter the plates with a velocity of 3.2479x109 cm/sec, and deflection sensitivity of 0.055cm/V. Determine: 1) The dimensions of vertical deflection plates {long, a part (l,d)}. 2) The distance from the end of deflection plates to the screen. { 2.5cm, 0.3cm, 38.49cm}
A shunt generator supplies a 30kW load at 215V through cables of resistance, R = 110mn. If the field winding resistance, Rf =680 and the armature resistance, Ra =45mn. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,
Q-2: The Si transistor circuit of the figure shown, find the emitter resistor (RE) that would bias for operating about VcEo = 5V. Let ICEO = 0, B-80, Rg = 220KN, RC = 2KN and Vec = 12V, where Ic # Ig. %3D Vec Re RF Ce RL Rs Vs RE
Q-2: The Si transistor circuit of the figure shown, find the emitter resistor (Rg) that would bias for operating about VeEo = 5V. Let IcEo = 0, p-80, R; = 220KO, R. = 2KA and %3D %3D %3D Vec = 12V, where Ie # Ig. Re RF tho Ce RL. Rs Vs RE
Sub:communication Need solution please
2. Write an OCTAVE program to plot the signal given below. P- Pmax Sin(21Ift); where Pmax= 10 MW, -60 Hz. %3D Find out time period and verify it with graph. Assume necessary data.
To study the input and output characteristics of a BJT in Common Emitter(CE) Configuration and plot it on graph.lab report Input Characteristics: V CE = 5V V CE = 10V V BB (volts) V BE (volts) I B (µA) V BE (volts) I B (µA) Output Characteristics: I B = 431μA (VBB=5V) I B = 930μA (VBB=10V) V CC (volts) V CE (volts) I C (mA)
hi=33
In an Amplitude modulator, the carrier is v. = -12 sin[2n(100 x 103)t]. If the modulating signal is Vm = 3 cos[2n(800)t)]: a) Determine the equation of the modulated signal b) Sketch the frequency spectrum of the modulated signal (label amplitudes and frequencies) c) Calculate the effective voltage of the modulated signal