O A) 1.35 A O B) 1.15 A OC) 1.25 A O D) 0.95 A O E) 1.05 A

Q: Exercice2: Show the state table of the following state diagram

A:

Q: In a DIA converter, LSB represents 0.2 V. The digital input is (0111) will cause an analog output of…

A:

Q: Sketch the Current through through cach Zenner diode 7v+ "Δ 1042 www 3v 5K2 Sve #2.5v

A: Zenor diode

Q: The total turn ON time of SCR is 40 µs. If the sum of delay and spread time is 8 us, the rise time…

A: for a scr , ton=tdelay+trise+tspread given tdelay + tspread = 8 μs and ton = 40 μs

Q: Typical Values of B range Oa from 1000 to several thousands O b. less than 1 to several minus hunds…

A: The explanation is as follows.

Q: Determine the aspect ratio of the NMOS in the circuit to produce a drain current of 150 uA. R2 2.5k…

A:

Q: What is the voltage, vp, across the diode? 3Ω 4Ω my 9 V ip VD 6 V O 9.0 V 6.0 V O Ov O 7.71 V

A: First calculate open circuit voltage of the diode . If voltage across diode is greater than zero…

Q: Cuffent Heralgh te 22 resisty Ming Nerfon's Heegpem. find Hte

A:

Q: A clamper circuit has 20 Vp-p, 100 Hz square wave input voltage. The circuit consists of silicon…

A:

Q: C VIN VOUT In this circuit, R= 800 ohms and C = 1 F. The input vIN Consists of two sine-wave…

A:

Q: Calculate the value of the capacitor in the ful wave rectifier filter as shown below. Knowing that…

A: In this question we need to find a capacitance C so that ripple factor is 5% of the given bridge…

Q: Determine the peak input voltage (Vpćim), peak output voltage (Vp(out), the average voltage (VavG)…

A:

Q: QUESTION 10 What is the PIV thru each diode? Use approximate diode model. 110Vrms 5:1 O 31.11V O…

A: In this question we need to find the PIV of the given bridge rectifier.

Q: Use the information provided here to determine the value of I lp (mA) 10 9- Si 10 V RI kn Va 0.5 0.8…

A:

Q: 1. A thermocouple is used to measure the temperature in a Junction Temperature (°C) Output Voltage…

A:

Q: 5. For the following circuit sketch the output of vo 10 ΚΩ Vi 10 V K -10 V 16 5.3 V- Si 7.3 V- +

A:

Q: If the ammeter parameters due to insertion include 1200 internal resistance and a load resistance of…

A: Given, Internal resistance, Rint=120 Ω Load resistance, RL=2 kΩ Let the source voltage is V

Q: A (0 – 12) A range ammeter has naccuracy of + 2.0% of its full scale. Calculate the % error in…

A: Given: A (0-12) A range ammeter Inaccuracy/limiting error on full scale +2.0% Expected value is 3.7…

Q: What is the frequency and what is the period, write the formula

A: Frequency is nothing but repetition of signal per second

Q: O 0.3 O 0.5 O 0.7 O 0.9 O 1.1 O 1.3 O 1.5 O 1.7

A: Answer: t = 0.5 seconds

Q: sketch the output waveform of the following circuits

A: The given circuit is a clamper circuit that shifts the DC line either in the positive side or…

Q: Analyze this circuit J Q Y K B D Q Clock

A: Given Circuit From above circuit we can see that it is a positive edge triggered circuit Lets go…

Q: 2. The harmonic spectrum of the following figure belongs to the input current of which of the…

A: To solve above problem, one should know what three phase semi converter is and how it is working. To…

Q: In figure 5, C = 10uF and the frequency of the signal V; is 1KHz. Draw Vo. diode is ideal.

A: Given: A clamper network,  with input waveform,  with C=10μF and frequency of input is 1 KHz.  To…

Q: Q3/ Design Colpitts oscillator to generate sine wave with frequency equal to 3 KHz, with gains equal…

A: It is given that: f=3 kHz

Q: 13 In the figure shown, the output voltage Vo is equal to model. si VS +5V KI o R 2K ol tovo D₁ Si…

A: In this question we will find output voltageusing diode approximation model.....

Q: Q Determine The Output Waveform And Calculate The current and PIV 10 V 72 T 1kQ si 1kQ 1kQ si

A:

Q: S1-The waveforms in the figure are applied to D-type FF. Accordingly, draw the shape of the signal…

A: Explanation: The above circuit of the D flip-flop shows that the triggering of the circuit is a…

Q: Find the Ceg for the circuit given below: 2 C Cea 2C O 20 O 1.5C O 10 O 2.5C

A:

Q: A (0 – 13) A range ammeter has inaccuracy of + 2.0% of its full scale. Calculate the % error in…

A:

Q: Ex. 304 See Figure 280. G(s) =1007( (s+2)(s+ 6) ), H (s) =1, and R(s)=1/s (unit step input).…

A: It is given that: Gs=100s+2s+6Hs=1Rs=1s

Q: Note :answer two questions only. Q1. draw output waveform of this circuit: 10v 12

A: The solution can be achieved as follows.

Q: What is the value of I? A) 0.1 A B) IA C) -1A 1A(1 70 IA D) -2 A E) 0 A

A: Given circuit,

Q: Q4) Draw the output waveform for the circuit in figure below. 2- Vin C1 R1 www 1ΚΩ 0.1μF 0 2 4 -2- 1…

A: An ideal inverting op-amp has this property, that the current flowing in both the feedback and input…

Q: Refer to the given figure. Determine the output voltage, VOUT. V1 50mVpk 1kHz 0" 741 U1 6 Vo R2…

A:

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.