Non-destructive testing of large molded pieces may be performed using radiation. Discuss what constructive elements a non-destructive testing system should contain, what type or properties they should have, how they should be arranged in relation to the analyzed piece and what information would indicate that a piece has not been molded correctly (e.g. air gaps in the internal structure). Could the size of such an air gap be calculated?

Non-destructive testing of large molded pieces may be performed using radiation. Discuss what constructive elements a non-destructive testing system should contain, what type or properties they should have, how they should be arranged in relation to the analyzed piece and what information would indicate that a piece has not been molded correctly (e.g. air gaps in the internal structure). Could the size of such an air gap be calculated?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ Determine the shear stress at points A and B on the beam if it is subjected to a shear force of V=400 kN. Represent the state of stress on a volume element of these points. 100 mm 100 mm 100 mm 100 mm 100 mm 100 mm R
Determine the force in members DE, HG, Bc and BG of the turss Shown in and state if the members are intenstion or compreession
Q3: Find the magnitude, location and slope of the resultant of the force system shown below. k=30 N. F100 EN 53° 30 F50 &N. 3 m 1 m a4
Link AB is to be made of a steel for which the normal stress is 442 MPa. Determine the cross-sectional area (in mm2) for AB if P = 24.9 kNand d = 0.46. Round off the final aswer to four decimal places.
D) Determine the true magnitude and direction of the forces acting on the cylinder
Develop the Shear force and Bending moment calculations and draw the Shear force and Bending moment diagrams
Q1
Stress Txy is 100 N/mm² and acts on the plane AB of element ABC. The element has a value of e, which is 12.5 degrees to the vertical, y-axis. Assuming that plane AB has an area of 20mm², determine the magnitude of force resultant of Txy, resolved in the direction of TX₁Y₁- Number Answer in kN, to three significant figures. A B Tan C
According to what is given in the cross-sectional picture at Km 1; a) Determine the condition of the cross section in KM 2 and indicate the level difference between the inner and outer edges. b) Determine the condition of the cross section in KM 3 and indicate the elevation difference between the inner and outer edges.
(a) 20 400% 1-25. Determine the moment of the force with respect to the point A for each system shown in Fig. P1-25. The 100-lb force of Fig. Pl-25c is tangent to the circle of radius 5 ft. P1-25 (b) 1000
Q2)) Fill the following blanks: 1)) Tensile tests are used to 3)) The most application tests of applied static stresses to which materials can be subjected are ----------, ----------, ---------. 4)) Tensile stresses cause ----- and compressive stresses while shear stresses ---------, of the material. 5)) Engineering stress-strain is important in important in 6)) The unit of mechanical stress is while the true stress-strain is or while the unit of strain is 7)) In compression test, when specimen is compressed, its height is cross-sectional area is and its --------, 8)) Compression is in contrast to the tensile, the compression test contributes to the ,in stress with ----, elongation. 9)) The hardness test measures- 10)) There are several methods of hardness test, such as: - 11)) Hardness Test can be found in different scales, such as: 12)) The impact test describes the -------, and it often used to evaluate the material. 13)) There are many impact test types including the --- 14)) The…