Nitrogen gas at 90° F (MW=28) goes through a compressor, increasing its pressure from 10 psi to 65 psi. The temperature remained constant throughout. Determine the work in Hp for a steady flow process; ΔKE=0, ΔPE=0; mass flow rate of nitrogen is 2 lbm/min. Round up to 4 decimal places. Draw and label the P-V and T-S diagrams.

Nitrogen gas at 90° F (MW=28) goes through a compressor, increasing its pressure from 10 psi to 65 psi. The temperature remained constant throughout. Determine the work in Hp for a steady flow process; ΔKE=0, ΔPE=0; mass flow rate of nitrogen is 2 lbm/min. Round up to 4 decimal places. Draw and label the P-V and T-S diagrams.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 29RQ: If 3000 ft3 of air is crossing an evaporator coil and iscooled from 75F to 55F, what would be the...

See similar textbooks

Similar questions

Show your complete solution for each problem. Only the final answer in your calculation should be rounded off to two decimal digits. Box your final answer. 1. The increase in the specific internal energy is 33.8 BTU/Ibm in a reciprocating compressor draws 40 lbm/min of air whose density is 0.074 lbm/ft³ and discharge it with a density of 0.311 lbm/ft³. At the suction, the pressure is 18 lb:/in² and discharge 88 lb:/in². If the changed in kinetic energy was neglected, determine the work on the air in horsepower (hp).
Oxygen (molar mass 32 kg/kmöl ) expands reversibly in a cylinder behind a piston at a constant pressure of 3 bar. The volume initially is 0.0125 m and finally is 0.0304 m; the initial temperature is 18.35 C. Calculate the specific gas constant with the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as = 0.917k|/kgkand molar gas constant as = 8,314 / kmol K
=conetant procabese n=0 -n=½ n=2 n=1 7 A fixed mass of an ideal gas undergoes a polytropic process, from an initial pressure, temperature and volume of 180 kPa, 40°C and 1.5 m³ to a final temperature and volume of 180°C and 2.6 m³. How much work is done by the gas in this process (in kJ)? Your Answer: units Answer ph
SHOW THE TABLE USED! A fixed amount of carbon dioxide goes through a polytropic process where n=1.4. The initial temperature of the CO2 is 250 K. The final temperature of the CO, is 400 K. If the mass of the CO2 is 12 kg and behaves as an ideal gas, determine the work, the change in internal energy, and the heat transfer during the process (in kJ). Note that PV=mRT. In this problem, can the carbon dioxide be considered an ideal gas at the initial conditions if the initial pressure is 150 kPa? Justify your answer quantitatively.
i. Draw a P-V graph to represent the changes undergone by the air ii. Calculate the maximum volume of the air. iii. What is the maximum pressure of the air? iv. State how the net work done on the air for the whole process can bedetermined.
A gas is in a container that is able to expand or contract so the pressure inside the container stays constant. The gas is steadily heated from 20 to 40 degrees Celsius. What is the percent change in the volume of the container? Governing Equation: Percent change in volume: Assumptions:
Oxygen (molar mass 32 kg/kmol)expands reversibly in a cylinder behind a piston at a constant pressure of 3 bar. The volume initially is 0.0148 m and finally is a.0333 m the initial temperature is 18.54 °C Calculate the specific gas constant with the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as- 0 .917kJ/kgK and molar gas constant as - 8.314 J/ kmol K
BOX YOUR FINAL ANSWER, ROUND UP TO 4 DECIMAL PLACES. Draw and label the P-V and T-S diagrams. 3. Nitrogen gas @ 90° F (MW=28) goes through a compressor, increasing its pressure from 10 psi to 65 psi. The temperature remained constant throughout. Determine the work in Hp for a steady flow process; AKE=0, APE=0; mass flow rate of nitrogen is 2 Ibm/min.
Show your complete solution for each problem. Only the final answer in your calculation should be rounded off to two decimal digits. Box your final answer. 3. During operation, steam with a flow of 4.68 lbm/s enters the system with an enthalpy of 1449 Btu/lbm and leaves at 1211 Btu/lbm. Using energy balance at the system, calculate the work (Btu) per unit time (min). The added heat to the system is 16.22 Btu/lbm.
! Required information A gas is compressed from an initial volume of 0.42 m³ to a final volume of 0.12 m³. During the quasi-equilibrium process, the pressure changes with volume according to the relation P=aV+ b, where a = - 1200 kPa/m³ and b= 1000 kPa. Gas P = a + b Calculate the work done during this process by plotting the process on a P-V diagram and finding the area under the process curve. (Please upload your response/solution using the controls below.)
Datos: P1(lbf)= 600 P2(lbf)=300 P3(lbf)=-550 I add the picture of the problem
1. I just need the graph or figure of it. One pound of an ideal gas undergoes an isentropic process from 95.3psig and a volume of 0.6ft3 to a final volume of 3.6 ft3. If cp = 0.124Btu/lb-R and cv = 0.093 Btu/lb-R, determine the final temperature of the gas (0F) and the work done by the gas (Btu).