Motors take electrical energy and produce O a Radiant energy Ob Thermal energy OC Mechanical energy O d. Chemical energy The register TEMP originally has 8 bits of zero values. Which of the below instructions allows us to obtain the binary number: b0000 1000 in the register? O a bsf TEMP, 1 O b. bsf TEMPA Oc bst TEMPO O d. bsf TEMP3

Q: Memory cell is the basic element of a semiconductor memory and it can store one byte? O a. True b.…

A: Semiconductor memory is a semiconductor device which can store digital data. Major semiconductor…

Q: Shown in the figure is timing diagram of a D-FF. Using the timing diagram determine which type of…

A: There are two types of clock pulse. 1-edge triggered -ve edge trigger +ve edge trigger 2-Level…

Q: 1. What is the purpose of using digital to analog conversion? 2. What is the sign of the output…

A: Digital to analog conversion

Q: What is the MUX1 select input while the "sltu" instruction is executing?     01     00     10…

A: Answer - C - 10

Q: In modeling of P controller, you need for block in Matlab. gain O sine wave оооо constant O step O

A: Types of Controller P controller I controller  D Controller  PI Controller  PD Controller  PID…

Q: Draw the output signal Q of the D-latch given the inputs Clock and D. The initial value of the clock…

A: Given:

Q: Write a loop which fills all of data memory (0 to 255) with Use 8051 assembly language.

A: The assembly language is made up of pieces that are utilized in a sequential order to build the…

Q: 5. How you can operate a DC motor work with 3.7 volt ? Keep in mind that the motor is controlled by…

A: According to the question we have to discuss how we can operate a DC motor work with 3.7volt.

Q: Q1: Hand trace the execution of the following program fragments showing what happens to the flags…

A: Let us assume that all the registers and flags have a value of zero initially. The instructions MOV…

Q: The lowest address contained in the ROM memory is: A13- A12- All C B 1 A10- El A 2 ROM 7 CS 0000…

A: The explanation is as follows.

Q: 13. Complete the following table according to the combinational logic circuit shown in figure below.…

A: According to the question, for the given circuit as shown belowWe need to fill the table shown below

Q: In the following instruction sequence, show the resulting value of AL after highlighted comment, in…

A: The given instruction sequence is shown below: mov al, 01101111b and al, 00101101b,        ; mov…

Q: Create the complete count sequence table and draw the timing diagram:

A: To Create the complete count sequence table and draw the timing diagram:

Q: 2- Draw the timing diagram for the following counter Logic "1" UP/DOWN ClockPulse J QA FFA CLK K QA…

A: Given:Circuit of up-down counter,we need to draw: timing diagram.

Q: Design the circuit that displays 35861429 on the seven segment display (just one). Use shift…

A: To design a circuit that displays the number 35861429 on a seven-segment display using shift…

Q: Convert the binary NUMBER 10111110010.11010 to decimal number (Show the steps in paper, scan and…

A: We will multiply 20, 21, 22.....to the binary digit from left side of decimal point and right side…

Q: Q6) Assume that we want to add the following instruction to the given MIPS single cycle data-path:…

A: According to the question, for the given MIPS operation, we need to find the condition of the…

Q: Find the word address for the following memory device shown schematic given below. Assume 24C01…

A: According to the question, for the given figure as shown below We need to find the word address.

Q: ITE 296 - Logic Cireuits and Demign ta Far 1. What is the output of Q and Q' respectively? Justify…

A:

Q: Ao Bo Cint A₁ B₂ Full Adder Full Adder So Couto S₁ Coutl

A: As we know that a full adder's logic diagram is made by  2XOR+ 2AND+1 OR Logic Gate like below and…

Q: Q1. Determine the contents of the register after execution of each instruction R16, $3F R18, $01…

A: Since you have posted multiple questions, we will solve the first question for you. If you require…

Q: Description: 1 is Serial In - Parallel Out (SIPO)shift register.Parallel In - what | Serial Out…

A: A register is usually used to store data for a period of time. Almost Every time, to create a…

Q: Assuming that DI=10016, DS= 140016, SI=FF0016, BX= AE0016, AX=100616 and the memory contents…

A: 1. Consider the given program, MOV SI, [BX+33H] This instruction used based indirect addressing…

Q: 11U. Analyze the following logic circuit: Jo Yo Qo Y, Q1 Y;' Q; K. Yo |K1 CLK CLK

A:

Code Conversion

The method or technique used to convert code from one format to another is termed code conversion. Code conversions are most commonly used in computers, digital electronics, microprocessors, etc.