microprocessor 8086given ss=0300 and sp =0040 for the instraction mov bx,7B3E,what will be the physical address after executing push bx command a)33F b)33E c)303D d)303E E)303Fthis is for push and what it will be if instead of push we use pop how ıt works

microprocessor 8086given ss=0300 and sp =0040 for the instraction mov bx,7B3E,what will be the physical address after executing push bx command a)33F b)33E c)303D d)303E E)303Fthis is for push and what it will be if instead of push we use pop how ıt works

Name: microprocessor 8086given ss=0300 and sp =0040 for the instraction mov
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: microprocessor 8086given ss=0300 and sp =0040 for the instraction mov bx,7B3E,what will be the physical address after executing push bx command a)33F b)33E c)303D d)303E E)303Fthis is for push and what it will be if instead of push we use pop how ıt

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter11: Operating Systems

Section: Chapter Questions

Problem 30VE

See similar textbooks

Similar questions

Assembly language x86 using MUL
physcal addresses are 4s ng 4 Ame dat in a cetain compe, te addresses can be translaled without y TLB entries At most how many ditina vid the address translation peh has 12 vld The Translation Look aside Bulfer (TLB)i sine is kB and the word size iby The memory is word addresible. The pe virtual addresses are 64 bea long d th sine is miss?
8086 microprocessor
LCPU assignment Multiply the number by 1.25: A = X * 1.25X = 0x3C (direct). Then save the result to main memory using direct addressing. Example: Multiply the value by 0.75: X * 0.75 = 0.5 * X + 0.25 * X X = 100 (0x64)100 * 0.75 = 750x64 = 01100100 00110010 [Shift 1x to the right - add 0 to the left and cut off one bit from the right]00011001 [Shift 2x to the right - add 00 to the left and truncate 2 bits from the right]01001011 [Sum of previous two transactions] 01001011 = 0x4b = 75
microprocessor 8086
Microprocessor 8086
O True O False Question 11 The decoding of 80x86 instructions are simpler than instructions in ARM processors. True O False D Question 12 All instructions of LEGV8 are 32 bits long. O True O False Question 13 In 80x86 assembly language, before calling a function or procedure, you must write a PUSH state address on the Stack. O True O False
. Assume SP=0XE99D, R16=0XE2, R17=0x25, R01=0XFC, R15=0X1F and the following memory information. Address contents (hex) post Address contents (hex) post pre 22 pre 44 OXE996 OXE99C OXE997 46 OXE99D C5 OXE998 17 OXE99E Аб OXE999 21 OXE99F 77 ОхЕ99A F2 OXE9A0 78 OXE99B C3 OXE9A1 A5 Find the values of the registers SP, R01, R16 and R17 after the following operations. РОP R01 РО R16 РОP R17 РOP R20 PUSH R15 SP R16 R17 R01 R20 R15
6-
Q:Find the value of SP address if SP= (2000) hex after execute the =following instructions SP PUSH A PUSH B PUSH C PUSH D إجابتك
Code a descriptor that describes a memory segment that begins at location AB208000H and ends at location AC20AFFFH. The memory segment is a data segment that grows upward and can be written. The instruction used is a 32-bit size. it is assumed that the privilege level of the segment was set at 2nd highest and that the segment has not been accessed.
intel 8086 microprocessor