МЕТНОD ОF JONT DETERMINE THE FORCE IN MEMBERS of the shown in figure 18kn 18kn 18kn 18kn 18kn 18ko 18kn 18kn

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Answer by true or false for the following       Specific heat is a measurement of the ability of the…

A: The specific heat of a substance is defined as the amount of heat to increase the temperature of the…

Q: two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their…

A: Given data: The diameter of pulley 1 is, d1 = 25 cm. The diameter of pulley 2 is, d2 = 40 cm. The…

Q: 10) in the following figure, if h2-10" and h1=5", then, the angle of taper equal 10" Ⓒa. 60⁰ Hand…

A: These are small blocks of alloy steel. Used in the manufacturing shops as length standards. Not to…

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: L-20 inches d-0.75 inch a-0.1875 inch Ea-10,000 ki Eb-17,000 ki Pa-Pb What is the thickness b?…

A:

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: It is a precision instrument with a low least count, and is used to take sub-millimeter dimensions…

Q: What is the temperature of an object where it is half as hot as 80 degrees Fahrenheit?

A: The temperature is 80°F The temperature of an object is half of the given temperature.

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: A puck weighs 10 lb and rests on the center of the frictionless surface of the ramp supported in…

A: Solution: Given Data: W=10 lba=38 inb=49.4 inc=19.8 ind=40.5 ine=41.8 inf=14.8 ing=51.2 in   To…

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: Help , Handwritten only. No Chatgpt

A:

Q: 38. A belt is to transmit 50 kw power to a machine. The sheave is 10 inches in diameter and turns at…

A:

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: Determine Stres

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: E 12.5 m C А 8 m 5 m

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: What is the mechanical advantage of this system?

A: We have to first draw free body diagram of the block and the pulleys and then derive a relationship…

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.