safety in general shown in picture

Q: Define Locked in loads

A: Load  - A load is a mechanical stress , moment or couple that a mechanical body is subjected to…

Q: For the following smooth channel roller support. Which of the following statements are true?   a.…

A: For the given system since all the surfaces are smooth thereby no friction will act on the surfaces…

Q: discussion of the temperature distribution problem along rod

A: We will use the fin analogy , a cylindrical is heated at the base and cooled by convection , had…

Q: Galvanized shet has a protective coating of- -in steel shects. Sodium Aluminum Magnesium Oc Zinic

A: Galvanization or galvanizing  is the process of applying a protective zinc coating to steel or iron,…

Q: wo components are to be connected by bolts. One of components is relativel nnection is disassembled…

A: Stage 1: One of the segment is relatively thick.  It is cleared from outlines that initial two sorts…

Q: Define the following, Joint. Link. Joint space. Actuator space.

A: Joint: A point where two or more than two links are connected is known as joint. Link: It is a…

Q: Describe the potential hazard in the following picture in one paragraph?

A: Welding is a joining process in which metals, or sometimes plastics, are heated, melted and mixed to…

Q: the open circuit voltage and

A: Given; In a DC are welding operation, the voltage-arc length characteristics was obtained as,…

Q: 6.25 ft 12.5 ft , 12.5 ft , 12.5 ft , 12.5 ft Ans. B D F H FCE = 8,000 lb, T 15 ft FDE = 2,600 lb, T…

A:

Q: Explain the installation procedures of a flexible coupling

A: given; explain the installation procedures of a flexible coupling.

Q: If external loads applied to metals, how do it's respond? (Draw and show in figure

A: The response when external loads are applied on the metals

Q: What is a trip wire, and what is its purpose?

A: Answer :  Trip Wire :- It is a triggering mechanism activated through a thin wire or cord.

Q: What is the name of this part? a. coil spring b. butterfly valve c. none of the choices d. governor…

A: given; What is the name of this part? a. coil spring b. butterfly valve c. none of…

Q: explain what happened here.

A: Given: Load current - Voltage graph

Q: Give an example of calculating Safety Factor of bearing.

A:

Q: Explain the installation procedures of a flexible coupling

A:

Q: what is true in the lever arm below? a. it is unstable b. statically determinate but unstable c.…

A:

Q: 0. Given the following mechanism: how many degrees of freedom (DOF)?

A:

Q: Make a research topic and question about underground cables

A: Given Underground cable To find Research topic and question

Q: Lubrication is a method to reduce wear on surfaces that are not in close contact and act as a seal…

A: Lubrication is a method to reduce wear on surfaces that are not in close contact and act as a seal…

Q: Customary units to SI units by using the values listed for length and force as defined values:…

A: Distributed load is equal to load(force) acting per unit length of any member.

Q: Choose the WRONG STATEMENT about regular lay wire rope O a. It has less tendency to rotate under…

A: Correct Option:  d. It has less structural stability.

Q: Describe the format of a fence diagram and give an example

A:

Q: A ceiling fan has a light kit attached to the fan. What type of load is the light kit?

A: A ceiling fan has a light kit attached to the fan. What type of load is the light kit? Inductive.

Q: The minimum life of the bearing is the life which 90% of the bearings will reach or exceed before…

A: Life of bearing is expressed in hours. It represents that how long a bearing can work before the…

Q: . What elastomer sealing materials could be used with a petroleum-base fluid if the operating…

A: Elastomers (also known as rubbers) are a versatile group of materials that are used in…

Q: 4. (Ef-1 X¡)^2 =D1

A: Sigma indicates sum of ^ indicates power.   In order to solve this, the following equation should be…

Q: explain zeroth law with simple problem

A: The zeroth law of thermodynamics is the one which were derived after three laws of thermodynamics.…

Q: 9. The floating fastener formula is: 10. The clearance hole LMC diameter formula is 11. The formula…

A: Given data: we have to find  9. The floating fastener formula  10.The clearance hole LMC diamter…

Q: Explain the term ‘Effect of End Conditions on Critical Load of Columns'

A: Write the Euler's formula for the critical load on a column. Pcr=π2EIminLe2 Here, Pcr is the…

Q: Why wires are covered by rubber or plastic covering?

A: wires are covered by rubber or plastic due to prevent of electric shocks.

Q: What do u mean by the factor of safety 3,4....n?

A: Factor of safetyit is the ratio of the ultimate strength of a member to the actual working stress or…

Q: what is the formula for working out spring constant?

A: Spring constant is generally defined as the force per unit elongation.

Q: Earthing is not necessary for machines and metallic parts which are externally accessible is an…

A: This statement is false complete reason given in next step.

Q: Metal water pipes and structural metal qualify as grounding electrodes. Select one: TRUE

A: given: Metal water pipes and structural metal qualify as grounding electrodes.

Q: Select one: A. Have low resistance to compression set B. Have a high modulus of elasticity C.…

A: As per given question  Mechanical seals are required to

Q: e Taylor's principle with Plug and Ring Gauge with figure.

A: The given problem is based on metrology.    Taylor's Principles: Go gauge should be design on…

Q: The col type Ka Select c a. b. Е С. С O d. E

A: please check your option once

Q: failure Mode why bellows corrosion.cause of corosion bellows and their solutions

A: Given Bellow To find Cause of corrosion Solution to corrosion

Q: Problem 8.2 The power source characteristics is given by l²=- 350 (V – 90) and the volt- age-length…

A:

Q: The standard emf and galvanic series are different in three ways; they are and

A: The standard EMF series,  provides a ranking of various half-cell reactions in terms of their…

General safety guidelines

Safety guidelines are the set of rules and codes that must be followed in the workplace for the occupational safety of workers, the machines, and the equipment that are present inside the workshop premise. There are many unsafe conditions and hazardous materials inside the workshop that makes prey for certain risk factors associated with health conditions. Extreme safety precautions must be taken inside the work area just like the precautions and practices that are been followed for Corona Virus Disease 2019 (COVID-19). People can also educate themselves by joining various health programs and camps. These will provide them with the necessary skills and knowledge about safety awareness. Occupational Safety and Health Administration (OSHA) thrives to create a safe and healthy environment for the workers working in the industries and provides them with proper education and training.