Material Strengths: Fy= 248 MPa, Fu = 400 MPa The channel (C180X14.6) is connected with four M16 bolts to the 12 mm thick gusset plate as shown. Determine the following: A-LRFD: Capacity based on Yielding on Gross Area B-LRFD: Capacity based on Fracture on Net Area C-ASD: Capacity based on Yielding on Gross Area D-ASD: Capacity based on Fracture on Net Area 100 40 * 40 -O O ** Channel gusset plate 100 →

Material Strengths: Fy= 248 MPa, Fu = 400 MPa The channel (C180X14.6) is connected with four M16 bolts to the 12 mm thick gusset plate as shown. Determine the following: A-LRFD: Capacity based on Yielding on Gross Area B-LRFD: Capacity based on Fracture on Net Area C-ASD: Capacity based on Yielding on Gross Area D-ASD: Capacity based on Fracture on Net Area 100 40 * 40 -O O ** Channel gusset plate 100 →

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explain/Draw Stress-Strain graph of mild steel when subjected to tensile force. Also write down the minimum Tensile (yield, ultimate strengths) and Ductility (percent elongation) requirements for Grade 60 (G60) as per ASTM A615
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem What is the value of S if the joint is 80% efficient? Tension of Plates = 76 MPa Hole diameter (effective) = 23 mm
Puzzler: Most steel reinforcing bars manufactured in the U.S. exhibit a sharp yield plateau. Two exceptions, however, are bars that are quenched and tempered and bars that are coiled immediately after they are hot rolled. The coiled bars are later straightened by a fabricator. Both (1) quenched-and-tempered bars and (2) straightened bars have stress-strain curves that are initially linear, but yielding is gradual, producing what is described as a "round-house" curve. The reason for the round-house behavior is the same for both types of steel. Why do these two types of reinforcing steel exhibit gradual yielding rather than a sharp yield plateau even if the same steel exhibits a sharp yield plateau if it is not quenched and tempered or coiled?
determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa Subject: Civil Engineering Steel Design
please answer completely. need asap
A mild steel bar of 2cm is subject to tensile test. The bar yields under a load of 80kN. It reaches a maximum load of 150kN and breaks finally at a load of 70kN. Estimate the a) Average tensile stress at yield point b) ultimate tensile stress c) average stress at the breaking point if the diameter of the fractured neck is 1cm
What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
Asap pls
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
A fillet-welded Joint of 6mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108MPa. The safe load that can be transmitted by the joint is 100mm 50mm
Problem 4 Given two welded plates n A36 plates t= 3/ • fillet size w=1/4" Electrode Fexx= 70 ksi • plate width = 9" ● ● ↑ t=¾/2" = 2) = Pu= smaller of (1) A(2) w=1/4" Base Metal Strength, DRn is given by: ÞRn = 0.75(0.6Fu) (tBM)(Lw) t=3/8" Determine max Pu that can be applied to this connection ? hint: Dobtain Pue based on weld strength (transverse) BM strength = where tbm = thickness of the thinner connected plate Lw= length of the weld Fillet weld this side only i.e. lw= 9 in کہ ۔ Ри opy
1