Mario is attempting to fix some Mushroom Kingdom plumbing.At one point in the plumbing, a horizontal pipe is carrying an incompressible frictionless fluidof density 1.33x10³ kg/m³.The pipe narrows from d₁= 6.2 cm at left to d₂ = 2.5 cm at right, as shown below.Td₂上If the fluid enters the wider left end of the pipe at a speed of 1.71 m/s, by how much must thepressure drop or rise (in kPa) at the narrower right end of the pipe? Be sure to include theappropriate sign (negative for a decrease in pressure; positive for an increase in pressure)!

Answered: Image /qna-images/answer/4f7de947-2e83-4cca-b373-ecb78de21959.jpg

Mario is attempting to fix some Mushroom Kingdom plumbing. At one point in the plumbing, a horizontal pipe is carrying an incompressible frictionless fluid of density 1.33x10³ kg/m³. The pipe narrows from d₁= 6.2 cm at left to d₂ = 2.5 cm at right, as shown below. TUL d₂ If the fluid enters the wider left end of the pipe at a speed of 1.71 m/s, by how much must the pressure drop or rise (in kPa) at the narrower right end of the pipe? Be sure to include the appropriate sign (negative for a decrease in pressure; positive for an increase in pressure)!

Mario is attempting to fix some Mushroom Kingdom plumbing. At one point in the plumbing, a horizontal pipe is carrying an incompressible frictionless fluid of density 1.33x10³ kg/m³. The pipe narrows from d₁= 6.2 cm at left to d₂ = 2.5 cm at right, as shown below. TUL d₂ If the fluid enters the wider left end of the pipe at a speed of 1.71 m/s, by how much must the pressure drop or rise (in kPa) at the narrower right end of the pipe? Be sure to include the appropriate sign (negative for a decrease in pressure; positive for an increase in pressure)!

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 54PQ: Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius...

See similar textbooks

Similar questions

(a) How high will water rise in a glass capillary tube with a 0.500-mm radius? (b) How much gravitational potential energy does the water gain? (c) Discuss possible sources of this energy.
(a) What is the density of a woman who floats in freshwater with 4.00% of her volume above the surface? This could be measured by placing her in a tank with marks on the side to measure how much water she displaces when floating and when held under water (briefly). (b) What percent of her volume is above the surface when she floats in seawater?
(a) A water hose 2.00 cm in diameter is used to fill a 20.0-L bucket. If it takes 1.00 min to fill the bucket, what is the speed v at which water moves through the hose? (Note: 1 L = 1 000 cm3.) (b) The hose has a nozzle 1.00 cm in diameter. Find the speed of the water at the nozzle.
In an immersion measurement of a woman's density, she is found to have a mass of 62.0 kg in air and an apparent mass of 0.0850 kg when completely submerged with lungs empty. (a) What mass of water does she displace? (b) What is her volume? (c) Calculate her density. (d) If her lung capacity is 1.75 L is she able to float without treading water with her lungs filled with air?
You are pumping up a bicycle tire with a hand pump, the piston of which has a 2.00-cm radius. (a) What force in newtons must you exert to create a pressure of 6.90105 Pa (b) What is unreasonable about this (a) result? (c) Which premises are unreasonable or inconsistent?
A rock with a mass of 540 g in air is found to have an apparent mass of 342 g when submerged in water. (a) What mass of water is displaced? (b) What is the volume of the rock? (c) What is its average density? Is this consistent with the value for granite?
Water is moving at a velocity of 2.00 m/s through a hose with an internal diameter of 1.60 cm. (a) What is the flow rate in liters per second? (b) The fluid velocity in this hose's nozzle is 15.0 m/s. What is the nozzle's inside diameter?
A manometer is shown in Figure P15.36. Rank the pressures at the five locations indicated from highest to lowest. Indicate equal pressures, if any. FIGURE P15.36
A U-tube open at both ends is partially filled with water (Fig. P15.67a). Oil having a density 750 kg/m3 is then poured into the right arm and forms a column L = 5.00 cm high (Fig. P15.67b). (a) Determine the difference h in the heights of the two liquid surfaces. (b) The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height (Fig. P15.67c). Determine the speed of the air being blown across the left arm. Take the density of air as constant at 1.20 kg/m3.
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
Review. In a water pistol, a piston drives water through a large tube of area A1 into a smaller tube of area A2 as shown in Figure P14.46. The radius of the large tube is 1.00 cm and that of the small tube is 1.00 mm. The smaller tube is 3.00 cm above the larger tube. (a) If the pistol is fired horizontally at a height of 1.50 m, determine the time interval required for the water to travel from the nozzle to the ground. Neglect air resistance and assume atmospheric pressure is 1.00 atm. (b) If the desired range of the stream is 8.00 m, with what speed v2 must the stream leave the nozzle? (c) At what speed v1 must the plunger be moved to achieve the desired range? (d) What is the pressure at the nozzle? (e) Find the pressure needed in the larger tube. (f) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.) Figure P14.46