M1 and M2 are matched, what is the output common mode voltage? Draw the output wave form if Vi is a sine wave of 10MHz and peak amplitude of Vdd/4, assume high gm, long channel, find the output signal shape, frequency and peak to peak amplitude, Rin ww RF VDD M2 Rout

Q: Solve the collector-emitter voltage (VCE) of Figure 612. VCC T8V Beta = 110 R2 3.9kQ Figure 612…

A: We need to find out collector to emitter voltage for given circuit

Q: 02: For the circuit in the figure below, assuming Vin-30V: 1. Determine the output voltage Vourat…

A:

Q: Please explain step by step (like the charging and discharging) how the output of this uncompensated…

A: The above circuit consists of a lead compensator made of resistors and capacitors. To this, a square…

Q: Voc빵12V Ic Rc=560ohm R3=100kohms в VCE VBE E B=100

A: Let us assume that transistor operate in active mode  Vbe=0.7 KVL in outer loop  Vcc=IB RB+Vbe…

Q: A chopper has input voltage of 290 and the load resistance as 50, the average load current as 50A.…

A: Chopper: The circuit which transfer the dc power from one circuit to another circuit at the required…

Q: Vi Ru Ri Vz 2. I, R2 = 3837.79 Q. R1 = 3763.67 Q. R3 = 3989.3 Q. R4 = 2898.06 N. V1 = 4.8 V. V2 =…

A: L

Q: P3 Design a relaxation oscillator circuit giving a triangular signal. The oscillation frequency is…

A: Relaxation oscillator in electronics is a type of non linear oscillator circuit which develops the…

Q: Discuss how the circuit produces a Frequency Modulated Signal

A: According to the question, we need to discuss the working of the circuit shown below

Q: The main element of AM peak detector is: Select your answer. BJT Op-amp Diode FET

A: The give problem is from Amplitude modulation The solution is given in the next step

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.0 k

A:

Q: 20Vp Vout 9V 15V Group A Even SIDS Draw output wave for this circuit mentioning maximum and minimum…

A:

Q: A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Id. O a.…

A:

Q: After quantization, the analog signal has Select one: a. finite amplitudes O b. infinite amplitudes…

A: After quantization, the analog signal has  a. finite amplitudes b. infinite amplitudes c. finite…

Q: Describe its frequency spectrum. What will be the output if the sampled signals are analog signal…

A:

Q: a) Design a Schmitt Trigger, draw the circuit diagram for the following condition. UT = 3.5 Volts;…

A: As per company guidelines we can solve only first question kindly post another question separately

Q: A chopper has input voltage of 290 and the load resistance as 50, the average load current as 50A.…

A:

Q: You are tasked to look for a converter circuit design that has the specifications tabulated in Table…

A: Given: In this question, the given details are, The aim is to produce an output voltage of 20 V…

Q: the given comparator and input signal V, draw the output waveform w.r.t the sinewave input signal…

A:

Q: Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered…

A: The Given circuit is full wave rectifier where R=2KΩC=1μF

Q: A chopper has input voltage of 270 and the load resistance as 7N, the average load current as 53A.…

A:

Q: In a Common Emitter (CE) Fixed Bias (FB) configuration, the input impedance is almost equal to ---_?…

A:

Q: Vdc please show the circuit in the figure as a Chaotic Oscillator. Show it using one of the…

A:

Q: scribé the function of signal conditioning in this block diagram. 5V 12V hermocouple 50 mV; output…

A: The thermocouple is a perfect example for an analog input device. As the signal conditioning system…

Q: Find stability of the system -alti h Ct) = e

A: If integration yields a finite values then the system is said to be stable

Q: A chopper has input voltage of 290 and the load resistance as 52, the average load current as 50A.…

A: The circuit transfers the dc power from one circuit to another the circuit at the required output…

Q: (1) (11) R₁ R: C₁ DIS TRI THR VCC RST C₂ 100 nF 555 Timer OUT CV GND Figure 4(b) -Vcc - 12V Vout The…

A: Given: An astable multivibrator with oscillation frequency = 1200 Hz and duty cycle = 88 %. We have…

Q: if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20…

A: A cut off frequency magnitude response is 3 dB lower 0 Hz. Formula cutoff frequency :  fc = 1(2π RC…

Q: Clamper circuit: Vi (p-p)= 10 volt (Sinewave) F=1 kHz R= 10 Kohm V= 4 volt C= 1 micro F Find and…

A:

Q: For a common-emitter amplifier, R = 10 k, RE = R = 150 Q, r'e = 502, and Bac value of the voltage…

A: Right Answer option (C) 50

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.