LQ2. A 40-kg mass rests on the top of the folding workbench with a 50-kg mass with mass center G. Calculate the tension in cable FH and the x and y components of the force in the pin at E.

Q: Determine the shear and moments in the floor girder as a function of x. Assume the support at A is…

A: ASKED: To write the shear and moment in the floor girder as function of x.

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

A:

Q: Determine the maximum shear and maximum moment in the Girder 6 (Girder BE). (All dimensions are in…

A:

Q: Cable ABCD supports the loading shown. determine the tension in member BC, angle B1 and B2

A: To find tension in cable BC and angle beta 1 and beta2

Q: Cable EI is used to support the bascule bridge at E. The weight of the deck gives result to the…

A: First we will find all the reaction support. Then, we will apply section method by cutting the…

Q: 2UKN 10okW wheel Icads 12m

A:

Q: A steel girder is part of highway 251A bridge in OK. Inspection reports have indicated that some…

A:

Q: Draw shear and moment diagram

A:

Q: I. Method of Members 1. The portable table shown is to support a load P = 1.5 kN at a variable…

A: P (load) = 1.5KN L = 1.5m

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each cable.

A: Given:- 600 lb = m Three cables To find:- Ta,Tb,Tc

Q: Cable ABCDE supports the loading shown. Determine the tension in member DE, the value of Yd and the…

A: Determine the tension in member DE, the value of Yd and the value of Yb

Q: *2-8 Part of a control linkage for an a rigid member CBD and a flexible cab applied to the end D of…

A:

Q: has a diameter of 40 mm and 24 mm, respectively. A horizontal member AC carries a linearly…

A: Equilibrium Condition is applied . Shear stress = shear force / Area  Tensile force in steel cable…

Q: (2 DETERMINE THE FORCES IN THE 2 ft CABLES AND BOOM 2 ft BO OA. 3 ft 250 llb

A:

Q: Cable ABCDE supports the loading shown. Determine the tension in member DE, the value of Yd and the…

A:

Q: For the frame shown below: a) Determine its support reactions, b) Draw the shear force diagram and…

A:

Q: Problem#1) For the post-tensioned beam shown in the figure find the maximum usable moment capacity…

A: Aps =1.53 in2 As per ACI 318-19, fps=2701-0.280.755.34×10-42706=268.96 ksi Compressive block depth,…

Q: The frame is composed of members connected byfrictionless pins. Draw free-body diagrams of each…

A: Draw FBD

Q: Determine end moment for all member and reaction at the support, and then draw SFD and BMD for frame…

A: Given  A frame Required  End moment of all member,  sfd and bmd.

Q: Situation 1| Simply Supported Beam ABCDE below carries multiple loads as shown. A built-up section…

A:

Q: Determine the tension, T, in the cable support which is attached at point B, and also the l'artesian…

A: Objective: To determine the tension in the cable and the Cartesian components of the reaction at A.…

Q: 15 kN F E D 6 m A B C E8 m-8 m–

A:

Q: A drawbridge is being raised by a cable EI. The four joint loadings shown result from the weight of…

A:

Q: 5 20lw 30KJ 2 13 4m lokaj A 3m 3m 3m 3 y

A:

Q: 8-21 The offset link has a width of w = 200 mm and a thick- ness of 40 mm. If the allowable normal…

A: Step 1: formula of Stress(Oallow)Oallow = P/Area , Area = width(thickness) Step 2: solve now for…

Q: member of the in figure,'using Compute the force in each Warnen Truss Shown the methed 0f seetions.…

A:

Q: E 4 m 1 m 50 kN/m 6 m A B 16 m - 8 m

A:

Q: QIA rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and…

A:

Q: The absolute maximum moment for the girder below will be at point A B C. 5 @4 m 20 m O A NON OF THEM

A: Given data Beam  Panel distances. To find out  Absolute maximum bending moment

Q: lear. 7. A beam ISMB 450 @ 72.4 kg/m transmits a shear of 150 kN and a moment of 130 kN-m to the…

A:

Q: Find the tension in the Active tension bracing in the center bay (hint: again, there is no need to…

A: Given:- It is given a truss of tension members and asked to find the tension in the active tension…

Q: INUTO: Tom C] Draw the shear force V and bending moment M diagrams for the frame showr - Te

A: Given:- To find:- Shear force and bending moment diagram Concept:- Shear force diagram displays the…

Q: G H A 5 kN/m 81 8 m L I B 3 kN/m 8 m K J C 5 kN/m 8m F E D

A: It has been asked in the question to Draw the approximate moment diagrams for each of the five…

Q: N 2. Determine the tension in the cables by the method of your choice. 14 A 60° 45° W = 12.5 KN www…

A:

Q: Determine the maximum weight W that can be supported as shown. Cable FG has a maximum strength of…

A:

Q: The rigid structure BCD is supported as shown. Assume a = 5.4ft, b-4.3ft.c-2.4 ft.d-1.9 ft, and…

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.