Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internalcylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downwardtraingular load with maximum intensity qo as shown.Linear q(x)2M122cSegment 1Segment 20.5 EIEl(a) Find expression for maximum compressive stress at point 1.(b) Find expression for maximum tensile stress at point 1.

∑FY=OR1×qoL2-12q02L3=0R1=-16q0L Solution Taking moment 1,…

Lonsider the nonprismatic cantilever beam of circular cross section shown. cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward beam has an internal

Lonsider the nonprismatic cantilever beam of circular cross section shown. cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward beam has an internal

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A rectangular cantiliver wooden beam is applied by point load of 400in at free end Determine cross section area and second moment of inertia about bending axis and Draw internal effects shear and bending diagram Determine direct and shear stress at A on cross section of a-a .sketch state of stress
Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radius r ) in segment 2. The beam is loaded by a downward traingular load with maximum intensity q0 as shown. (a) Find expression for maximum compressive stress at point 1. (b) Find expression for maximum tensile stress at point 1.
A beam has a hollow circular cross section 40 mm outer diameter and 30 mm inner diameter. It is made from metal with a modulus of elasticity of 250 GPa. The maximum tensile stress in the beam must not exceed 350 MPa. Calculate the following. (i) The maximum allowable bending moment and (i) The radius of curvature. A beam has a hollow circular cross section 40 mm outer diameter and 30 mm inner diameter. It is made from metal with a modulus of elasticity of 250 GPa. The maximum tensile stress in the beam must not exceed 350 MPa. Calculate the following. (i) The maximum allowable bending moment and (i) The radius of curvature.
The rigid bar AB is hinged at A and supported by a steel plate hanger. The hanger is fixed at C and bolted at D with two plates.Given: Width of plate hanger= 50 mm Thickness of plate hanger = 10 mm Bolt diameter= 20 mm Allowable bolt shear stress= 68 MPaAllowable bolt bearing stress= 250 MPa a.What is the allowable stress in the hanger based on bolt capacity in double shear at D. b.If the maximum tensile stress in the hanger is 138MPa, find the allowable load W
If the beam is subjected to an internal moment of M=30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. V Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm 150 mm M 15 mm
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? Please answer this with FBD please. Thank you.