locations Use the graphical method to constuct the shear-force and bending-moment diagrams for the beam shown. Label all significant points on each diagram and identify the maximum mements along with their respective locations. Clearly differentiate straight-line and curved polions of the diagrams Curved Print P the diagrams differentiate straig hinge 30KN 1.5m 10KN/m 7b A 2m 20 KN C 2 dime 20KN/m 3m at 124

locations Use the graphical method to constuct the shear-force and bending-moment diagrams for the beam shown. Label all significant points on each diagram and identify the maximum mements along with their respective locations. Clearly differentiate straight-line and curved polions of the diagrams Curved Print P the diagrams differentiate straig hinge 30KN 1.5m 10KN/m 7b A 2m 20 KN C 2 dime 20KN/m 3m at 124

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use Slope-Deflection metod in determining the following the reaction at the given supports and show the shear and moment diagram of the beam E = 210GPa and I=1350x10^6 mm^4
12.18 0A and Aa. Reactions given. I=2690 in.*. 30 k 60 k A 10 ft 10 ft 15 ft 15 ft 20 ft 30 ft 2.62 k 65.63 k 21.75 k can you solve this problem with Conjugate Beam Method? E = 29*10^6psi %3D
QI/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension T in CD of 1.2 kN. Express T as a vector. Does it make any difference in the result which coordinate system is used? Ans. T = 0.321i + 0.641j – 0.962k kN, IC 1.5 m B 1.5 m G T= 1.2 kN 3 m 2 m 1.5m 3 m
For the frame system shown below, find the deformations at D using the principle of virtual work. please Use the integrationtables that I will give you
Find the reactions of the given beam using Slope Deflection Method
The beam is subjected to the distributed load and the couple shown. If M is slowly increased starting from zero, at what value M0 will contact at B change from the lower surface to the upper surface?
Question 3 Consider the two forces F en F2 acting on the post in Hibbeler (edition 14) Problem 2.134 p 80. 3.1 Determine the angle 0. F, = 400 N 3.2 Determine (a) the projection of F, on the line of action of F2 and (b) the correspon- ding component related to the projection. Express your answers in cartesian vector form. 35° 120° y Note: The projection of F1 on the line of action F2 is parallel to F2, and most likely not equal to F2. 60° 20° 45 3.3 Determine the projection of F2 on the line of action of F1 as well as the correspon- ding component. Express your answers in cartesian vector form. F; = 400 N
Subject: STATIC OF RIGID BODIES FIND: x and y of the centroid in mm. Thank you!
Solve for the end moments using the 7-step matrix method of the following beams. 200KN |160KN 32KN/m 2m 2m 2m 4m A B
Analyze the loaded beam as shown. Be guided as follows: Solve for the reactions at supports Draw Shear and Moment Diagrams Compute for deflection at A (AA) and slope at C (0c) using Conjugate Beam Method a. b. С. 50 kN 90 kN D A C 6 m 9 m 9 m El = constant E = 70 GPa %3D I = 95 (106) mm4
Determine the static and kinematic indeterminacy for the following structures.
Use the method of virtual work and determine the vertical displacement of joint B of the truss. Each steel member has a cross-sectional area of 300 mm2 E = 200 GPa. 5 m 3 m 80 kN 3 m -4 m-