Locate the centroid y of the cross-sectional area of the beam constructed from a channeland a plate. Assume all corners are square and neglect the size of the weld at A. Take a =310 mm, b = 365 mn(Figure 1)1 of 1>Express your answer to three significant figures and include the appropriate units.Figure?µAy = 12mm20 mm ySubmitPrevious Answers Request Answer10 mmX Incorrect; Try Again; 5 attempts remaining70 mm( Return to AssignmentProvide Feedback

To find Centroid about you axis

Locate the centroid y of the cross-sectional area őf thể Beai and a plate. Assume all corners are square and neglect the size of the weld at A. Take a = 310 mm , b = 365 mın (Figure 1) Express your answer to three significant figures and include the appropriate units. jure 1 of 1 ? HA mm 20 mm y Submit Previous Answers Request Answer 10 mm X Incorrect; Try Again; 5 attempts remaining 70 mm < Return to Assignment Provide Feedback

Locate the centroid y of the cross-sectional area őf thể Beai and a plate. Assume all corners are square and neglect the size of the weld at A. Take a = 310 mm , b = 365 mın (Figure 1) Express your answer to three significant figures and include the appropriate units. jure 1 of 1 ? HA mm 20 mm y Submit Previous Answers Request Answer 10 mm X Incorrect; Try Again; 5 attempts remaining 70 mm < Return to Assignment Provide Feedback

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thumbs up will be given. No long explanation. Answers are given. Write the complete solutions legibly.
Two forces of magnitude TA = 6159 kips and TC = 7180 kips are applied as shown to a welded connection. Knowing that the connection is in equilibrium and angle X is 43.9°, determine the magnitude (kips) of TB . Round off only on the final answer
What is the diameter required?
Q3/ For the plate shown in figure below find * (a) Z A YA 7 9 8
Problem 2.63 The bolt is subjected to the force F, which has components acting along the z. y, z axes as shown. Part A If the magnitude of F is 76 N, and ax=52° and y= 50°, determine the magnitude of Fz component. Express your answer to two significant figures and include the appropriate units. ANSWER: F₂ = 40 N Incorrect; Try Again; 4 attempts remaining Part B Determine the magnitude of Fy component. ANSWER: Fy= your answer to significant figures and inclu the appropriate units. Part C Determine the magnitude of F₂ component. Express your answer to two significant figures and include the appropriate units. ANSWER: F₂ =
Y Y Determine the moment of each force about the bolt located at A (Figure 1). Take FB = 45 lb. Fo= 30 lb Figure < 1 of 1 Y 2.56 Part A Determine the direction of the moment produced by FB- clockwise Ocounterclockwise Submit Request Answer Part B Determine the magnitude of the moment produced by FB- Express your answer with the appropriate units. μÅ 346 OB My about A Value Units Submit Request Answer Part C Determine the direction of the moment produced by Fe O clockwise counterclockwise 9.75 Submit Request Answer Part D Determine the magnitude of the moment produced by Fc. Express your answer with the appropriate units. HA S C Mpe about 4 = MEC A Value Submit Request Answer Part n ? Units ?
X =0
An A36 angle bar is used as a tension member connected on both legs with 20 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number.
From the figure shown, diameter of holes is 20 mm. Compute the net area for the plate if the thickness of the plate is 10 mm.
Hand written an clean solution please
Engineering Mechanics UPVOTE WILL BE GIVEN. Please write the complete solutions legibly. No long explanation needed. Answer in 3 decimal places. Box the final answer.
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.91 in2, A? = 0.31 in2, P1 = 81 kips, P2 = 47 kips, P3 - 31 kips and E = 29x106 psi %3D %3D Your final answer should have three decimal places A1 A2 B. D' P3 P1 P2 -/- --16 in 12 in. 12 in.