Locate the centroid of the two figures.

Q: A spring, having an unstretched length of 1.0 m has one end attached to the 5-kg ball, as shown.…

A:

Q: Can you write a small research on the Applications of Hydrocarbon Fuels?

A: Hydrocarbon fuels are adaptable items utilised in every end-use sector, including residential,…

Q: A bicycle and a rider of mass 90 Ry of 15 km/hr on the level road. A brake is applied to the rear…

A: Given: The bicycle and rider mass, m = 90 kg The rider speed, v = 15 km/hr The diameter of wheel, d…

Q: a small taper on the sides of a wheel rim? Why is an automobile tyre usually black in colour? What…

A: Rims are basically designed for the minimization of dislodging of the tire when they are subjected…

Q: Four-tenths kilogram (0.3 kg) of a certain gas is contained within a piston-cylinder assembly. The…

A:

Q: The viscosity of blood is 4x0x10-3 Pa x s. Calculate the pressure difference (in pascals) due to…

A:

Q: An open coiled heilcal spring made of 6 mm diam- eter steel wire and 60 mm mean coil diameter, with…

A: We know that an axial torque T is applied to an open coiled helical spring made of 6 mm diameter…

Q: A three-legged tube is filled with oil (SG = 0.88). As shown, the surfaces of oil in all legs are at…

A:

Q: A bicycle and a rider of mass 90 kg are travelling at the rate of 15 km/hr on the level road. A…

A: Given that,    Mass of bicycle and rider, m=90 kg    Speed of bicycle, v=15 km/hr=15×10003600=4.1667…

Q: Determine the specific volume, in m3/kg, of ammonia at 50°C, 2 bar, using (a) Table A-15. (b) Figure…

A: Find the specific volume of ammonia at 50°C , 2bar .

Q: Describe the features, components, electric propulsion systems, and working principles of electric…

A: given; Describe the features, components, electric propulsion systems, and workingprinciples of…

Q: 3 KN Q.3) Find the force in each member of the truss by using joint method, if a pin support at A…

A:

Q: A = 5 in^2 E = 29,000 ksi I = 5 in^4 Setup [k] and Solve for the displacemen

A:

Q: 03/ The manually - operated hoist shown in figure (13) is based on an epicyclic gear train. The sun…

A: Given: The number of teeth on annulus, Za = 90 The tangential force on handle = 25 x load lifted

Q: A motor car has a wheel base of 2.82 m has pivot centres 1.2 m. The track distance between tyre…

A: The radius of a turning circle indicates the amount of space required to turn a vehicle. As a…

Q: Q5 Explain by sketch only5 of the following: 1- the effect of heat rolling on grain size 2- three…

A: The size and texture of hot strip grains, as well as their distribution over the strip…

Q: The volocity fiold for a flow is given by: V= (5x + 6y- 72) i- (6x + 5y + Sz)j + (3x + 2y + Az)k and…

A: This question is related to the kinematics of fluid. the conservation of mass means velocity field…

Q: he figure shows a weapon called a battering ram (modern large battering rams are typically mounted…

A: Wr=2500 lbkE=6.5ftDistance between C and D=6fth=4.5ft d=3ftθ=10°vE→=4.5ft/s    To-Find:- 1.  aE→=?2.…

Q: Q(2): Three masses (A, B and C) with mass (20, 25 and 12 kg) respectively. The radius of rotation…

A:

Q: Analyze the truss using methods of joints

A:

Q: 3. Consider the force system in equilibrium shown in the image below. Determine the following: a.…

A: To draw the free body diagram.

Q: Give all the example and the proper uses of Pneumatic Power tools and the PPE needed during the…

A: To find :- Pneumatic tools and their applications

Q: Initially saturated water liquid at 200°C is contained in a piston-cylinder. The water is then…

A:

Q: Q2. A. Given is 1 hr-UH for a certain catchment. Derive the 2hr.-UH I hr.-UH (1-mm) for the…

A:

Q: (b) Between a solid mass of 1P kg and floor, two slab of isolator, natural rubber and felt are kept…

A: Given that, Matrix number format=AD 200107≡xPQRSTP=0, Q=0, R=1, S=0, T=7,Mass of solid mass, m=1P=10…

Q: The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It…

A:

Q: (b) Why are the clutch friction plates perforated? What is the purpose of installing coil springs in…

A: Clutch friction plates are perforated for coolant passage for heat dissipation. Perforation helps in…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Solid and geometric modeling

A: According to the details provided in the question, we need to create a solid model of the given…

Q: A grave digger digs a grave with a varying force F equals 10 plus s squared Newtons, where s is in…

A:

Q: A 2-meter long prism with square cross-section of side 0.1m is made of stainless steel with a…

A:

Q: Q1- Determine the normal force Nc, the shear force Vc, and the moment Mc at point C. Assume the beam…

A:

Q: What is perfect steering? Derive expression for the basic condition for a perfect steering…

A:

Q: . . coffee at breakfast O drinks O drink O drank

A: Drinks- present Drank- simple past Drunk- past principle

Q: A steel rod 3 m long is secured between two walls, if the load on the rod at( 10°C ). Determine the…

A:

Q: Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The spring…

A:

Q: A is rotating in the counter-clockwise direction at a speed of 180 r.p.m. increasing at the rate of…

A: NAO=180rpmωAO=2π×18060=18.85rad/sOA=180mm=0.18mCB=240mm=0.24mAB=360mm=0.36mBD=540mm=0.54m

Q: The bending stress at point A.

A: Given data Outer Diameter of Shaft = Do = 50 mm = 0.05 mInner Diameter of Shaft = Di = 40 mm = 0.04…

Q: d Given: 9/8 in Diameter of bolt = 7/8 inch V2 in Diameter at the root of the thread (bolt) = 0.731…

A:

Q: A Mansard roof truss is loaded as shown. a) Identify, by observation, any zero force members in the…

A:

Q: Question 4 Determine the normal force, shear force, and moment at point C of the beam in Figure 4.3…

A:

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: Find the force by using method of joints. Determine wether it is tension or compression

A: Calculate the reaction at the support, Since there is no support showing the truss. let us assume…

Q: 11 A crane hook is of trapezoidal cross-section hav- ing inner side 80 mm, outer side 30 mm and…

A:

Q: 3. Consider the force system in equilibrium shown in the image below. Determine the following: a.…

A:

Q: A bituminous coal has the following composition: C = 71.5% H = 5.0% O = 7.0% N = 1.3% S = 3% Ash =…

A:

Q: In the truss system shown, calculate (a) the reations at support A and I, (b) The forces in each…

A: Only normal reactions will be obtained on these two supports At I there will be two X and Y…

Q: 9-86 Flat-plate solar collectors are often tilted up toward the sun in order to intercept a greater…

A:

Q: 25m (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer…

A: Given data:- Inner diameter = 40 mm Outer diameter = 50 mm Torque = 2.5 kN-m Moment = 3.6 kN-m Find…

Q: An oil pumping rig is shown in the figure. The flexible pump rod D is fastened to the sector at E…

A:

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.