(LO-3,LO-7) An experiment is performed by using the circuit given below. In the circuit R = 110 kQ and the voltage of battery is 18.0 Volt. When the switch is turned of, the time to see voltage on voltmeter as 5 V is measured. The average time is determined as to be 3.8 seconds. What is the capacitance of capacitor?

(LO-3,LO-7) An experiment is performed by using the circuit given below. In the circuit R = 110 kQ and the voltage of battery is 18.0 Volt. When the switch is turned of, the time to see voltage on voltmeter as 5 V is measured. The average time is determined as to be 3.8 seconds. What is the capacitance of capacitor?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Calculus If R is the total resistance of two resistors which are connected in parallel with resistances R1 and R2 then If the resistances are measured in Ohms as R1=27Ω, R2=48Ω with possible error of 0.50% in each case, estimate the maximum error in the calculated value of R.
I did a physics lab and got some values. I want to check them theoretically to see how the results differ. From this diagram, answer the following questions: The laws to be verified included the conservation of current in a node, the addition of potentials for components in series, and the addition of currents for components in parallel. NOter that the second battery was connected in the opposite direction to the current, this is the aim of the question. The data : R1: 1094 ohm R2 : 998 ohm R3: 1094 ohmR4: 25 ohm Source 1 : 5 V SOurce 2 : 1,5 V
Q 15 please
What is the value of the time constant (in ms) for the circuit below?
a) If the current in this circuit is 3 A, what must be the value of R3? b) What is the voltage drop across the 2 ohm resistor? c) What is the voltage drop across the 3 ohm resistor. d) What is the power used in the circuit in amps?
1-Equivalent capacitance read in multimeter when two equivalent capacitors with 470 µF theoretical values used in the experiment link above are connected in parallel; (you fill the Ceg- theoris and Cerror) Seg-experimental = 959.5 µF Seg-the =. =....... 2- -Equivalent capacitance read in multimeter when two equivalent capacitors with 470 µF theoretical values used in the experiment link above are connected in series; (you fill the Ceg. theeriç and Cerror) Seg-experimental = 240.5 µF Seg-the =. 3- Equivalent capacitance read in multimeter when three equivalent capacitors with 470 µF in series Seg-experimental = 159.7 µF Seg-the =. = u....
Interpret In (AVR) = In (AV) -t as y(t)=b+mt T and get the result: graph of In (AVR) versus / (called a semi-log graph) should be linear with y-intercept b = ln (AV) and slope m = 1 =-²/ T We can determine t and hence C from an experimental measurement of the slope. Draw a graph of In (AVR) (log of measured voltage across the resistor, vertical axis) vs time (horizontal axis). From the y-intercept of the best-fit line, find AVo = 9[V], as expected. Using the slope, find T = Using this calculate the unknown capacitance: T Cexperimental R - - 1 slope = Now, measure the actual value of the capacitance with the digital multimeter and compare it to the value obtained from the graph: Actual capacitance is: 12,4 FI
Determine the current in the circuit when the charge on the capacitor is 1/7 of its maximum value (in p.A). Show all work and look correct answer
Assume that you want to measure the voltage on a circuit component and the multimeter that is used for this measurement has ranges 0.2V, 2V, 20V, and 200V for DC Voltage measurement. When you chose the 2V range for the measurement, you obtained 1.43V as a result and you recorded it with the corresponding error of the measurement as Vmeasured=1.43+0.02V. Below, you can see the other three results obtained from measurements with other ranges of the multimeter. Please choose the correct ranges used for each measurement. Vmeasured = 1 ± 2V Choose.. Out of range warning Choose... Vmeasured = 1.4 ± 0.2 V Choose...
Integrated ConceptsHow much time is needed for a surgical cauterizer to raise the temperature of 1.00 g of tissue from 37.0oC to 100oC and then boil away 0.500 g of water, if it puts out 2.00 mA at 15.0 kV? Ignore heat transfer to the surroundings.
The space between the plates of a parallel-plate capacitoris lled with two slabs of linear dielectric material, parallelto the plates. Each slab has thickness L, so that the totaldistance between the plates is 3L. Slab 1 has a dielectricconstant of 2, and slab 2 has a dielectric constant of 2.5.The free charge density on the top plate is σ and on thebottom plate is -σ.a) Find the electric displacement ~D in each slab. b) Find the electric eld ~E in each slab.c) Find the polarization ~P in each slab.d) Find the location and amount of all bound charge.
ela R L 2L lenda 6 Pail 1) Consider two cylindrical copper resistors (wires). The shorter wire length L and radius R. The longer wire has length 2L and radius. a) Call the resistance of the shorter wire Rs and the resistance of the longer wire RL. What is RL in terms of Rs b) At a Constant voltage V what are the respective currents Is and IL in terms of Rs or RL? Which has a greater current.