Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14 × 1214⁢ × 12 -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 3838 -in.-diameter pins, while member BCD is connected to its support at B by a 516516 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 2.85 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. Link AC is made of a steel with a 65-ksi ultimate normal stress and has a x-in. uniform rectangularcross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, whilemember BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steelwith a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 2.85 isdesired, determine the largest load P that can be applied at D. Note that link AC is not reinforced aroundthe pin holes.8 in.Bin.C6 in. 4 in.→→The largest load P that can be applied at Dislb.

Answered: Image /qna-images/answer/a76b038f-382c-432d-ae1e-074f8575cb7f.jpg

Link AC is made of a steel with a 65-ksi ultimate normal stress and has a x-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at Cby-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 2.85 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. T 8 in. B in. C 6 in. 4 in.- The largest load P that can be applied at Dis lb.

Link AC is made of a steel with a 65-ksi ultimate normal stress and has a x-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at Cby-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 2.85 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. T 8 in. B in. C 6 in. 4 in.- The largest load P that can be applied at Dis lb.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.5.2P

See similar textbooks

Similar questions

A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000 lb and F = 3000 lb. 12 in- 6 in 6 in- 13 in F A 13 in B Figure P-912 -12 in- ¯¯Â 2 in 6 in Cross- Section
ACTIVITY The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with thickness shown in the figure. The working stresses are 70MPa for shear in rivet and 140MPa for bearing stress due to the rivets. How many 19-mm diameter rivets are required to fasten the said members to the gusset plate? K.R.R.P. wwwwwwww 00 400 4m B 3m C 96KN 4m 6m 200KN E Am 3m F 96KN 4m H DETAIL OF JOINT B 75X75X6 mm ------------- · ET---- I 14 mm thick GUSSET PLATE P BC 75X75X13 mm P BE
Trusses 1. Find the stresses of FAB. FAC., FBC & FBD- 20 k 15 k D 60° 60 60° 5' 10 10 Ra Rb
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN
Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional area of AB. Assume that the link will be adequately reinforced around the pins at A and B. There is no given factor of safety.
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.