length and diameter are D and L, respectively. The heat flux at the wall varies linearly along the channel. Show that the water temperature at the exit of the channel is given by: 46. Consider the flow of water in a heat flux controlled channel. The channel -(Ginlet + d'exit ) mc p Texit = Tinlet + 2

length and diameter are D and L, respectively. The heat flux at the wall varies linearly along the channel. Show that the water temperature at the exit of the channel is given by: 46. Consider the flow of water in a heat flux controlled channel. The channel -(Ginlet + d'exit ) mc p Texit = Tinlet + 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

With reference to the figure below a power station uses condensor in order to condensate steam for re-use. Water flows through the shaded area and steam through the smaller tubes. The water is at 40 degrees celcius and the flow rate required to keep this temperature balance is 0.52 m³/s. Calculate the hydraulic mean depth. 1.018 m 3.231 m 1.288 m D = 2m QUESTION 10 d = 80mm QUESTION 9 With reference to # 8 what flow condition is present in the condensor? O Transition Laminar O Turbulent With reference to #8 what is the mean velocity of water if the flow reaches the highest laminar flow value?
Engish (en) uestion 2.5- 50 2.5 -80- 1.5- 70 1.5 0.5- 0.5 100. Lake 06 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Kilometer If aquifer hydraulic conductivity, hydraulic gradient and effective porosity are found to be 0.4 m/day, 0.05 and 0.3 respectively, calculate total discharge (Q) across the northern side of the map? The aquifer lower boundary is horizontal and always has a (-11) m elevation. Note: Q = K.A.G (Q = must be a number in m3/day, e.g. 23405 m3/day or 23405) %3D Answer: حد عنده فكره كيف يحلوا هالسوال؟!
State the three characteristics of each of the following I. Laminar II. Turbulent
Discussion 1- Indicate the factors affecting the Reynotes number (Re). 2. The limits are gaved to the Reynolds number (Re) that if they less than 2000 it is the laminar flow and if they more than 4000 The flow is turbubent but there is a possibility to change those limits. 3-Discuss the importance of the infinite medium. Worksheet No. Risc of W.L. in Time for Risc in Collecting Tank (cm) W.L. (sec.) 1 s 45 2 s 26.5 3 s 21.5 4 % 12.75 s s 7 6 s s Diameter of pipe = 1.8 cm Length of pipe = 87 cm Area of Collecting Tank = 13 x 8.5 cm® @ Temperature of water = 30
8. An open water tank has two inlets and one outlet. The water flow rate through the two inlets are ( 0.01 m'/s, and 0.00785 m'/s), and the water flow rate from the outlet is (0.0231 m'/s). Does the water level in the tank inereasing, decreasing, or remains constant? And if it is increasing or decreasing, at what rate this increase or decrease will occurs? Explain.
3. Vertical turbines are to be used for flocculation in a water treatment plant with a design flow rate of 189,270 m³/day. Flocculation is to be designed with two trains and five compartments per train. The total detention time in this process is to be 25 minutes, and the average temperature of the water flowing into the plant is 10°C. The velocity gradient in the first compartment is to be 70 s¹. Make the following design decisions for the first compartment: a) Determine the dimensions of the compartment. b) Determine the diameter of the impeller. c) Determine the water power required. d) Determine the maximum rotational speed. e) Estimate the pumping capacity of the impeller and circulation time in the tank.
What is the hydraulic diameter of a pipe with a rectangular cross section of width w and length twice the width?
SUPERPOSITION Question 1: (Multiple Wells) As shown in the figure below one recharging and 2 discharging wells are operated simultaneously. All the wells have the same diameter 30 cm. The discharge of the recharging well is 85 lt/s and the discharges of the discharge wells are identical and is 70 lt/s. The original piezometric (or water table) level within the aquifer is 50 m. Storage and transmissivity values are 0.0002 and 0.0015 m²/s respectively. If the wells are operating simultaneously (i.e. the flow condition is unsteady) what is the drawdown at the discharging well A at time t-30 hrs, if the aquifer is: 40 m 24 m a- Confined [i.e. s= Q 4nT B Q=75 lt/s W(u)] Q=75 lt/s 18 m b- Unconfined [ i.e. s-- Q=85 lt/s s² 2h, 4nT W(u)]
1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm to water (p= 62 11m/ft²³) Ignore any changes in Kinetic or potential energy and Tassume isothermal flow C.e. internal energy is constant, this is the normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump with full energy Balance and simlifying to solve for the pump, Starting head symbolically. Then begin careful of units, Solve for pump head in feet. GIVEN: 35psi 500 gpm p=62 1bm/3 XA. 10.5 A B. 100.8 ft C. 50.1 ft D. 80.7f 35 500 62 (32.2) + 2(32.2) 35 + 500
fLUID MECAHNICS The flow in the piping system shown is 10 mgd. Determine (a) the head loss from A to D and (b) the flow in pipes 2, 3, and 4. Use C = 100 for all pipes. (a) head loss : _____________________ ft of water(b)Flow in Pipe 2: _____________________ mgd Pipe 3: _____________________ mgd Pipe 4: _____________________ mgd
1) You are designing a microfluidic device that will expose cultured cells (adhered to the bottom of the channel) inside two different chambers to an average shear of 1 dyne/cm? and 10 dyne/cm?. You chose to connect the chambers in series. The channels are rectangular with a uniform depth of 0.050 mm. a) Determine the total microchannel flow rate (Q) and the width of each chamber (w1, W10) to meet the design criteria. Use the fluid properties of water for your calculations. State any additional assumptions and define additional variables as needed. b) State one advantage of a series configuration over a parallel configuration. State one advantage of a parallel configuration over a series configuration.
A frustum cone tank is initially filled with water as R 2w shown in figure. After that, the water drains through a hole of radius (r=0.05 m) is located at the bottom of tank. 1- Find the depth of water at any time (y(t)). 2- compute the time required to drain half volume of water in the tank. where R=w w = 2m g = 10 m/s?