Least count of leveling staff is: O a. 0.5 b. 0.05 Ос. 0.0005 O d. 0.005

Q: Explain grid leveling.

A: LevelingLeveling is the method or procedure to determine the relative altitude of any point on the…

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: Define Land Drainage.

A: Drainage is a reverse method of irrigation  This is generally known as the removal / disposal of…

Q: Define Eccentricity,

A: Eccentricity is a term is used in the loading condition of the engineering. for example, the load on…

Q: Define Bearings?

A: Bearing: It is defined as the angle which is measured between the reference meridian and the survey…

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: A triangle has an area of 14 sq ft and a base of 7 feet. What is the height of thetriangle?

A: given data :  area of triangle (A) = 14 square feet  base (b) = 7 feet  height (h) = ?

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: Define Transform faults.

A: Transform fault is a kind of fault in which two tectonic plates slip past each other.

Q: In site design, what features matter the most?

A: This question is related to the Building design and construction from Civil Engineering. In this…

Q: Define the term Index Properties.

A: The index properties are the soil properties which help to identify and classify soil. These…

Q: Indicate briefly, using words or sketches, how geosynthetics have been used to prevent groundwater…

A: Applications of Geosynthetics that are used to prevent ground water contamination:

Q: Factors for planning include

A: before starting any project you need to do proper planning by using previous record , test…

Q: Explain the Eurocode terminology : GEO

A: GEO The application of scientific methods and engineering techniques and utilization of natural…

Q: geomorfologie

A: Note: As nothing is mentioned in this problem so, we are assuming that we have to only define this…

Q: What is the most important thing to ensure when it comes to layouting?

A: Civil surveying is a type of engineering that includes analysing and documenting information about a…

Q: what is the usual drawing paper size in preparing a lot plan ?

A: The drawing sizes for the construction plans will come in the different formats — with 18” x 24” and…

Q: What is the difference between interval and ratio level measurement scales?

A:

Q: What are the activities conducted by International Federation of Surveyors?

A: There are ten committees formed for conducting certain activities by FIG Committee 1- Practice for…

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: Define International Federation of Surveyors

A: The International federation of surveyors is a non government organization recognized by United…

Q: a. On the equator: b. Golden, Colorado: C. Barrow, Alaska: 0° latitude 39°44'N latitude, 105°12'W…

A:

Q: hat exactly is meant when the term "scope" is used?

A: The term "scope" describes the total set of goals and demands necessary to finish a project.

Q: ow many square yards are there in a 72” x 112 yard roll?

A: GIVEN  WIDTH = 72"   = (72" )* (1'/12")*(1 yard/ 3') = 2 yard Length = 112 yard

Q: What is National Spatial Reference System?

A: National Spatial Reference System  (NSRS) A consistent coordinate system that defines latitude,…

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: Level surface, Bubble line, Horizontal line, Level line, Line of collimation, Bench mark, Change…

A:

Q: With the aid of an illustration, describe two methods by which areas bounded by irregular lines can…

A: Areas bounded  by irregular lines can be found by using midoridnate rule , trapezoidal method ,…

Q: Define SLS requirement

A: Solution: A Service level specification basically forms a part of the service level agreement in…

Q: What is a site plan? Discuss it. (M Please cite reference as per APA

A: A site plan is a detailed drawing that shows the area where the building has to be constructed…

Q: Explain the Eurocode terminology :UPL

A: The Eurocode terminology :UPL

Q: Define Aerial Photographs.

A: Aerial Photographs:

Q: Q#4: Define Baseline, Main survey line, check line and tie line?

A: - Baseline, main survey line, check line and tie lines are mostly used in triangulation surveying to…

Q: Figure below represent contour lines for ground surface and wells located on it 50 w2 W1 fill table…

A: given-water table elevation of wells-W1=60W2=50W3=40

Q: D#2: Write different uses of Surveying?

A:

Q: Road survey including plan , L section & X-section

A: Road Survey : Road survey is the process to know the properties of the site to where new highway is…