Learning Goal: A beam with length L = 3 m is supported by a pin joint at A and a cable attached at Cas shown in (Figure 1). It is subjected to the distributed load with w₁ = 1.4 kN/m and ₂ = 1.8 kN/m. The angle between the cable and the beam is 8 = 40°. Determine the normal force, shear force, and bending moment acting at point B, located z = 0.7 m to the left of the end of the beam. gure Bx c < 1 of 3 ▼ Part E What is the internal shear force at point B? Assume the force acts as shown, and use the appropriate sign for your answer. Express your answer to three significant figures with appropriate units. ▸ View Available Hint(s) VB = -1.27 kN Submit ✓ Correct Part F Previous Answers What is the internal bending moment at B? Assume the moment acts as shown, and use the appropriate sign for your answer. Express your answer to three significant figures with appropriate units. ▸ View Available Hint(s) Submit ■μÀ MB = 0.950 Previous Answers kN•m ? X Incorrect; Try Again; 3 attempts remaining

Learning Goal: A beam with length L = 3 m is supported by a pin joint at A and a cable attached at Cas shown in (Figure 1). It is subjected to the distributed load with w₁ = 1.4 kN/m and ₂ = 1.8 kN/m. The angle between the cable and the beam is 8 = 40°. Determine the normal force, shear force, and bending moment acting at point B, located z = 0.7 m to the left of the end of the beam. gure Bx c < 1 of 3 ▼ Part E What is the internal shear force at point B? Assume the force acts as shown, and use the appropriate sign for your answer. Express your answer to three significant figures with appropriate units. ▸ View Available Hint(s) VB = -1.27 kN Submit ✓ Correct Part F Previous Answers What is the internal bending moment at B? Assume the moment acts as shown, and use the appropriate sign for your answer. Express your answer to three significant figures with appropriate units. ▸ View Available Hint(s) Submit ■μÀ MB = 0.950 Previous Answers kN•m ? X Incorrect; Try Again; 3 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*. If a resultant shear force, Vacting at the beam cross section is 40 kN, (a) Determine the shear stress at point M, N, O and P based on the given shear force. (b) Sketch the shear stress distribution over the cross section and label the shear stress values V= 40 kN M 80 mm 40 mm y =100 mm 80 mm 80 mm 30 mm 80 mm Figure Q3
points A, B and D, respectively, as shown in the figure. A uniformly distributed loac of 4 kN/m acting vertically downwards extends for a length of 4 m between point A and C. Page 3 of 6 5 kN 10 kN 4 kN/m A 2 m 2 m 1 m 2 m 30 kN Figure Q2: A cantilever beam 2.1. Calculate the magnitudes and directions of the support reaction force RE and bending moment ME and at point E. 2.2. Establish the equations of shear forces (SF) and bending moments (BM) for each span of the beam. 2.3. On the basis of the established equations for SF and BM for the cantilever beam, construct the shear force and bending moment diagrams along the entire span of the beam. 2.4. Determine the magnitude and position of the maximum bending moment acting on the beam. 2.5. Calculate and show the positions of the points of contra-flexure (PCE)
For the statically indeterminate frame shown in Figure 2, use the moment distribution methodto determine the moments at each joint and support. The members are fixed connected at the supports and joints. EI is the same for each member. Suppose that w = 18 kN/m, P1 = 3x kN,and P2 = 22.x kN. Then draw the SFD and BMD. x=9
Two street lights are mounted as shown in the figure one at A and the other at C. The member AD is able to freely rotate about D. Member BE is a steel cable. B. EACH street light has a mass of 5 kg, AB=20cm, BC=20cm, CD=10cm, DE=17.32cm. Assume gravity is 9.81 N/kg. h=4cm Draw the shear force profile (a) between point A and D. On the diagram, clear indicate the values on the diagram. (b) member just to the right of point B. Calculate the maximum bending shear stress. At what distance from the bottom does it occur? Consider a cross-section of the (c) distance from the bottom does the minimum bending shear stress occur? What is its value? For the same cross-section, at what
Q5
For the beam and loading shown in Figure 5, determine the value of (r) at the point of action of the resuitant force of the distributed load using point B as the origin. Parabola Vertex 2000 N/m 900 N/m B 6 m A Figure 5: A parabolic distributed load on a beam AB. Answer: If the loading were analysed using point A as the origin, would the value of w at the location of the resultant change? Select one: a. No b. Yes
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is oy = 473 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 77 mm, b=46 mm, a=11 mm, H=77 mm, d= 46 mm N b h a + N a | d H
Draw the shear and moment diagrams for the figure shown Show your solutions 80KN 40KN ▼ 30 KN/m v 3m 3m 3m
Find the Nominal force, N in kilo Newtons (kN). What is the shear force, V in kilo Newtons (kN). Find the bending moment, M in kilo Newton metres (kNm).
Q6
Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, be careful of the sign.
Please solve very soon completely