Lead shot may be manufactured by dropping molten-lead droplets into water.Assuming that the droplets have the properties of solid lead at 300◦C, calculate the time for the center temperature to reach 120◦C when the water is at 100◦C with h= 5000 W/m2 · ◦C, d =1.5 mm.

Q: Calculate the density of oxygen gas at a temperature of 57 C and a pressure of 5 MPa.

A: Density of oxygen at 570C and 5 MPa is asked

Q: In modeling a skin burn from an oven, when the exposure time is short, we can approximate the skin…

A: The depth of the damaged skin layer is to be determined for the given process.

Q: Describe the difference between average pressure and false pressure

A: The force applied perpendicular to the surface of an object per unit area over which that force is…

Q: 3. A long hollow cylinder has inner and outer radii R, and R2, respectively. The temperature of the…

A: Given details, For Hollow Cylinder of  Inner radius=R1 at Temperature T1 Outer radius=R2 at…

Q: Now explore the influence of the mass of the block. Using the copper block and a 4.0 second flame,…

A: Given that, The initial temperature of 10 g block T1 = 20oC The final temperature of 10 g block T2 =…

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: Match the type of calculation that must be used in determining the operating pressures of the…

A: The bubble point is the factor at which the first drop of a liquid combination starts to vaporize.…

Q: For multicomponent distillation,under what conditions is the pinch point located at the…

A: The condition at which pinch point is located at the location of feed is to be mentioned.

Q: temperature. * O True O False Nan

A: The above question is the question of the heat exchanger. There are many reasons that decrease the…

Q: Estimation of the viscosity of a dense gas. Estimate the viscosity of NITROGEN at 65°F and 1000…

A: It is given that nitrogen gas is at temperature of 65oF and pressure of 1000 psig.

Q: 5.3-6. Unsteady-State Conduction in a Brick Wall. A flat brick wall 1.0 ft thick is the lining on…

A: To solve this problem, we can use the following equation for unsteady-state conduction in a…

Q: Example 2.1 : Calculate the rate of heat loss through a wall of k = 0.70 W/(m K)] 5 m in length, 4 m…

A: Above problem is based on conductio.Conduction is an mode of heat transfer which is define as the…

Q: Explain how heat from the earth is converted into electricity

A:

Q: What are the changes in the number of moles of the components during a chemical reaction when they…

A: The changes that take place in the number of moles of the involved components in the chemical…

Q: Answer the question below: Experiment 1: Calibration of a Calorimeter Results Time (in minutes)…

A: Before HeatingTime minutes Temperature (C)024.50.524.61.024.71.524.82.024.92.524.93.025.0Heater…

Q: 2). Even though steel is about 7 to 8 times denser than water, a steel paper clip or razor blade can…

A:

Q: Convert 50 psia (lbf/in.2 absolute) to kPa:

A: The conversion of pressure from one unit to another is to be done.

Q: 5. . . ) In a manufacturing process, a long, coated plastic rod (p = 2200 kg/m³, c = 800 J/kg K, k…

A: The time it take to the surface of the rod to reach 175o C, the temperature above which the special…

Q: Choose the correct option: 8. Considering the physical and chemical properties, abundance, and even…

A:

Q: A radiation flux of 1000W/m' is incident upon a surface that absorbs 80 percent of the incident…

A: Radiation flux= 1000 W/m2= 1000 J/sm2Incidented area= 4 m2time of absorption=2h=2×3600=7200 sec

Q: Calculate the capacitance of a parallel-plate capacitor whose plates are 20cm x 3cm and are…

A: Area A = 20 x 3 cm = 20 x 3 x 10-4 m Distance between plates d= 1 mm=1 x 10-3 m New capacitance c'…

Q: What is the difference between an isothermal and an adiabatic flash?

A: Adiabatic Flash: A sudden pressure difference in at valve position, due to which a partial phase…

Q: Specific heat capacity is constant for all materials Select one: O True O False

A: Answer: False

Q: Radiant energy with an intensity of 700W/m2 strikes a flat plate normally. The absorptivity is twice…

A: The ratio of the energy of absorption, transmittance, and reflection is to be determined.

Q: Give at least 3 examples of under the Chemical Engineering Field that uses numerical analysis.…

A: Introduction :Numerical methods are used for solving mathematical problems that cannotbe solved…

Q: -dj- dz E50 mm PA X) mm da Pn

A:

Q: 4. Write any three differences between Geothermal and Tidal energy?

A:

Q: Estimate the thermal conductivity of the Meat at 35 ° C. (Water content = 75.0% wet basis). Thermal…

A: Thermal conductivity is the intrinsic property of the material, it actually relates the ability of…

Q: Calculate the accentic factor of oxygen gas at 30 C and 5Mpa.

A:

Q: When using an aspirator as a source of vacuum in a vacuum distillation, do you turn off the…

A: It is to be mentioned if the aspirator is turned off before venting the system or not.

Q: Effect of the carbon percentage on the shape and magnitude (mechanical properties) of stress-strain…

A:

Q: A glass container with an insulating cover with a surface area of (R + 160) cm2 and (R+11) mm thick…

A: Heat transfer is a process by which thermal energy is transferred from a high temperature body to…