3. Calculations and Discussion1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit andcompare it with measured value. For the capacitive filter, obtain the theoretical valuesof the DC output voltage and the ripple voltage and compare these values with themeasured quantities. Determine also the practical and theoretical values of the ripplefactor.2. Calculate the theoretical output DC voltage of the center-tapped full-wave rectifiercircuit and compare it with measured value. For the capacitive filter, obtain thetheoretical values of the DC output voltage and the ripple voltage and compare thesevalues with the measured quantities. Determine also the practical and theoreticalvalues of the ripple factor.3. Repeat the calculations for the full-wave bridge rectifier and filter circuit.4. Determine the peak inverse voltage (PIV) on each diode in the three rectifier circuits.5. If diode D4 in the bridge rectifier circuit of Figure 5 was removed or burned, explainthe operation of the circuit in this case and sketch the predicted waveform of theoutput.6. Explain the effect of increasing the filter capacitance on the output voltage in the half-wave rectifier and filter circuit.7. Compare the DC output voltages of the three rectifier circuits. Which circuit has thehighest output? On the other hand, which circuit has the lowest peak inverse voltageon each diode?8. What value of filter capacitor is required to produce 1% ripple factor for a full-waverectifier having a load resistance of 1.5kQ? Assume that the peak value of the outputvoltage is 18V.

Answered: Image /qna-images/answer/091f1099-4f06-40f2-814a-53a2c9020d45.jpg

late the theoretical output DC voltage of the half-wave rectifier circuit an are it with measured value. For the capacitive filter, obtain the theoretical value e DC output voltage and the ripple voltage and compare these values with th ured quantities. Determine also the practical and theoretical values of the rippi

late the theoretical output DC voltage of the half-wave rectifier circuit an are it with measured value. For the capacitive filter, obtain the theoretical value e DC output voltage and the ripple voltage and compare these values with th ured quantities. Determine also the practical and theoretical values of the rippi

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

For the circuit 1.Find the resonant frequencies ff, and fm : What do the results sugget about the Q, of the circuit s''p 2.Find the value scof X, and X, at resonance 3.Find the total impedance Z, at resonance 4.Find the magnitude of I,,and I, at resonance 5. Find Q, ,Q, and BW 6.Calculate V, at resonance C Z7, R R, E0.5 kn 1 AF Vc 40 mA 80.5 mH
LRC Circuits 200V 200Hz 30.0 peak w + 20.0 mH mn 5.0 μF
vo input terminals of an op-amp are connected to voltage signals of strength Theyo 754uand 740µV repectively. The gain of the op-amp in differential mode is 50 and CMMR is 80 dB. Calculate the output voltage and % of error due to common mode.
Subject:- Physics find the reatance and the impedance of the cicuit. calculate the current andthe resonance frequency of the circuit.
(a) What is the impedance? (b) What is the maximum current? A (c) What is the phase constant o of the power supply's emf with respect to the current?
-Series RLC ciranit Amplitnde of he Voltage Source is 120V - lesistor has a valve of 802 a value of 8os2 Reactance of ne capacitor is 480e The vellage amplitade acras the capucitar is 360V (a) What is he amplitude amplinade of The curent within the cirenit? (b) What is he impedance of he circuit? (c) What are hwo possible readance valves fur he induchr and whoh ore has a smaller anqular freg vency Than resonance frequency.
Please show the work, thank you.
Please create a comparison table between the 5 common configurations of BJT amplifiers: CE fixed bias, CE voltage divider bias, CE un-bypassed emitter resistance, CC (emitter follower) and CB. For each configuration, draw the circuit, and list the 4 main quantities which are the: input impedance, output impedance, voltage gain, and current gain.
The figure below shows the current i and driving emf & for a series RLC circuit. "Ay Is the phase constant positive or negative? The phase constant is positive. The phase constant is negative.
Q5: Analyze the single phase bridge inverter whose output voltage is a semi- square of 60% On-time at 50 Hz. The inverter is connected to 100V de source and its load is composed of 100 in series with 100mH inductance. 1. Sketch to scale load current waveform at steady-state (derive an expression for the peaks of the current in term of system parameters) and find its RMS value. 2. Sketch input current and output voltage waveforms. 3. The RMS value of output voltage and its components up to fifth harmonics. 4. Output steady-state power, power factor and power associated with each harmonics components up to fifth harmonics. 5. Find THD of the output signal. [Hint: V₁ =4E/(√na) sin nß/2] ← 48 Stitch It!